Does AGR hydraulic end, type ZBZ110, AISI 316L steel require a specific crimping sleeve size for BSP-threaded hoses with a 60Â° cone?

AGR hydraulic end, type ZBZ110, AISI 316L steel does not specify a single universal crimping sleeve size in the provided description. It is designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the specific type and size of hose being used. For BSP-threaded hoses with a 60Â° cone you must select a sleeve matched to the hose manufacturerâs recommendations (hose inner/outer diameter, reinforcement type and crimp profile) and crimping equipment. Verify sleeve dimensions and crimping specifications against the hose datasheet and perform manufacturer-recommended crimp testing to ensure a proper seal and mechanical integrity.

Can AGR hydraulic end, type ZBZ110, AISI 316L steel be used with stainless-steel crimping sleeves for corrosive environments?

Yes. AGR hydraulic end, type ZBZ110, AISI 316L steel can be used with stainless-steel crimping sleeves for corrosive environments, with the following conditions met: - Material compatibility: Both the fitting and sleeve being AISI 316L (or similarly corrosion-resistant stainless) ensures good resistance to many corrosive media, minimizing galvanic or crevice corrosion risk when in contact. - Correct sleeve selection: Use a crimping sleeve specifically designed for the hose type and rated for hydraulic service pressures and temperatures. The sleeve material should be at least AISI 316L or another compatible corrosion-resistant alloy. - Proper crimping process: Crimping must follow the hose and fitting manufacturerâs specified tooling, die dimensions, and parameters to ensure a leak-free, mechanically sound joint. Improper crimping can create crevices or stresses that promote corrosion or failure. - Surface finish and cleanliness: Ensure mating surfaces are clean and free of contaminants. Avoid dissimilar-metal debris or particles that could initiate localized corrosion. - Environmental considerations: 316L performs well in many corrosive environments (chloride-containing waters, industrial atmospheres), but for very aggressive media (strong acids, high-chloride elevated-temperature seawater) verify suitability; in some cases higher-alloy materials or coatings may be required. - Quality control: Inspect crimp integrity (visual, dimensional checks, pressure testing as applicable) and consider passivation after assembly to restore optimal stainless-steel corrosion resistance. If these conditions are observed, using AGR hydraulic end, type ZBZ110, AISI 316L steel with stainless-steel crimping sleeves is appropriate for corrosive environments.

AGR hydraulic end, type ZBZ110, AISI 316L steel

Q: Is AGR hydraulic end, type ZBZ110, AISI 316L steel compatible with standard crimping sleeves for BSP-threaded hoses with a 60Â° sealing cone?

Yes. AGR hydraulic end, type ZBZ110, AISI 316L steel is compatible with standard crimping sleeves for BSP-threaded hoses with a 60Â° sealing cone. The product description specifies it is a standard hydraulic end fitting (type Z) with external BSP thread and a 60Â° sealing cone (AGR), explicitly designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material AISI 316L does not affect crimping compatibility and offers corrosion resistance; ensure the crimping sleeve matches the hose construction and dimensions specified by the hose manufacturer and follow recommended crimping procedures and tooling.

All products, Fittings for high-pressure hoses/

Additional information

Material	SS – stainless steel
Standard length [m]	15, 30

Standard hydraulic end fitting (type Z – with a regular hydraulic “tail” for hose), with external BSP thread, 60° sealing cone (AGR). Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: AISI 316L steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZBZ110-02-04-SS	End. GZ 1/8" BSP, hose 1/4", cone 60°, AISI 316L	6		In stock	Enquiry
TI-ZBZ110-04-02-SS	End. GZ 1/4" BSP, hose 1/8", cone 60°, AISI 316	3	450	In stock	Enquiry
TI-ZBZ110-04-03-SS	End. GZ 1/4" BSP, hose 3/16", cone 60°, AISI 316L	5	450	In stock	Enquiry
TI-ZBZ110-04-04-SS	End. GZ 1/4" BSP, hose 1/4", cone 60°, AISI 316L	6	450	In stock	Enquiry
TI-ZBZ110-04-06-SS	End. GZ 1/4" BSP, hose 3/8", cone 60°, AISI 316L	10	445	In stock	Enquiry
TI-ZBZ110-06-04-SS	End. GZ 3/8" BSP, hose 1/4", cone 60°, AISI 316L	6	445	In stock	Enquiry
TI-ZBZ110-06-05-SS	End. GZ 3/8" BSP, hose 5/16", cone 60°, AISI 316L	8	445	In stock	Enquiry
TI-ZBZ110-06-06-SS	End. GZ 3/8" BSP, hose 3/8", cone 60°, AISI 316L	10	445	In stock	Enquiry
TI-ZBZ110-08-06-SS	End. GZ 1/2" BSP, hose 3/8", cone 60°, AISI 316L	10	415	In stock	Enquiry
TI-ZBZ110-08-08-SS	End. GZ 1/2" BSP, hose 1/2", cone 60°, AISI 316L	12	415	In stock	Enquiry
TI-ZBZ110-10-10-SS	End. GZ 5/8" BSP, hose 5/8", cone 60°, AISI 316L	16	350	In stock	Enquiry
TI-ZBZ110-12-10-SS	End. GZ 3/4" BSP, hose 5/8", cone 60°, AISI 316L	16	350	In stock	Enquiry
TI-ZBZ110-12-12-SS	End. GZ 3/4" BSP, hose 3/4", cone 60°, AISI 316L	20	350	In stock	Enquiry
TI-ZBZ110-16-12-SS	End. GZ 1" BSP, hose 3/4", cone 60°, AISI 316L	20	280	In stock	Enquiry
TI-ZBZ110-16-16-SS	End. GZ 1" BSP, hose 1", cone 60°, AISI 316L	25	280	In stock	Enquiry
TI-ZBZ110-20-16-SS	End. GZ 1.1/4" BSP, hose 1", cone 60°, AISI 316L	25	210	In stock	Enquiry
TI-ZBZ110-20-20-SS	End. GZ 1.1/4" BSP, hose 1.1/4", cone 60°, AISI 316L	32	210	In stock	Enquiry
TI-ZBZ110-24-20-SS	End. GZ 1.1/2" BSP, hose 1.1/4", cone 60°, AISI 316L	32	185	In stock	Enquiry
TI-ZBZ110-24-24-SS	End. GZ 1.1/2" BSP, hose 1.1/2", cone 60°, AISI 316L	38	185	In stock	Enquiry
TI-ZBZ110-32-32-SS	End. GZ 2" BSP, hose 2", cone 60°, AISI 316L	50	175	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Standard hydraulic end fitting (type Z – with a regular hydraulic “tail” for hose), with external BSP thread, 60° sealing cone (AGR). Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: AISI 316L steel.