Is the Adaptor 90Â° from GZ BSPT/GZ BSP, stainless steel, type A110 compatible with standard BSPT and BSP ports and do threads require additional sealing?

Yes. The Adaptor 90Â° from GZ BSPT/GZ BSP, stainless steel, type A110 is compatible with standard external BSPT (GZ BSPT) and external BSP (GZ BSP) ports. The design uses two different mating seals: the BSPT external thread provides thread sealing (tapered male BSPT thread seals on the mating female BSPT thread) and the external BSP (parallel) thread seals on a 60Â° cone. Therefore, when fitting to a matching BSPT port no additional sealant is required beyond correct tapered-thread engagement; when fitting the BSP (parallel) side the metal-to-cone contact is the sealing surface, so sealing relies on proper seating of the 60Â° cone. In practice you should follow torque and assembly instructions and, if requested by your application or standards, use appropriate thread sealant or a copper/JIC-style backup washer only where specified.do not apply sealant to the 60Â° cone seating face.

Can Adaptor 90Â° from GZ BSPT/GZ BSP, stainless steel, type A110 be used in high-pressure systems with different torque settings without leakage?

Adaptor 90Â° from GZ BSPT/GZ BSP, stainless steel, type A110 can be used in high-pressure systems provided correct installation and torque are applied. The seal design-BSPT sealing on the thread (tapered thread seal) and BSP sealing on a 60Â° cone-requires that each connection be tightened to the manufacturerâs specified torque to ensure proper metal-to-metal cone contact and thread deformation for sealing. Using different torque settings risks under-tightening (leading to leakage) or over-tightening (damaging threads, deforming the cone, or compromising the seal). Material AISI 316L offers good corrosion and strength for high-pressure use, but leakage control depends on correct torque, appropriate mating fittings, and adherence to pressure ratings and assembly procedures. For reliable, leak-free operation, follow specified torque values and installation guidelines.

Does Adaptor 90Â° from GZ BSPT/GZ BSP, stainless steel, type A110 require specific installation torque to ensure proper sealing?

Yes. Adaptor 90Â° from GZ BSPT/GZ BSP, stainless steel, type A110 requires correct installation torque to ensure proper sealing because it uses two different sealing methods: the external BSPT thread seals on the thread (tapered thread seal) and the external BSP thread seals on a 60Â° cone (metal-to-metal cone seal). Key points: - BSPT tapered thread: Requires sufficient torque to compress threads and create the interference fit that forms the seal. Under-tightening can leak; over-tightening can damage threads or distort the fitting, compromising the seal and material integrity (even in AISI 316L). Use recommended torque ranges for the specific thread size and lubricant/sealant (if allowed) to avoid galling and ensure repeatable sealing. - BSP 60Â° cone: The cone seal relies on correct axial clamping force to seat the cone surfaces. Proper torque ensures full contact of the 60Â° sealing surfaces without overstressing the cone. Uneven or insufficient torque leads to leaks; excessive torque can deform the cone or mating port. - Material and pressure: AISI 316L has good corrosion resistance but still requires careful torque control, especially for high-pressure applications. Use manufacturer torque recommendations for the exact thread sizes, pressure rating, and any mating components. If manufacturer data are unavailable, consult standard torque charts for stainless steel fittings of the specific BSP/BSPT sizes and apply appropriate anti-seize or thread lubricant where specified. - Assembly best practices: Clean threads and cone surfaces, inspect for damage, use specified sealants only if permitted (note that cone seals typically should not use tape on sealing faces), hand-start then tighten with a calibrated torque wrench to the specified value, and retighten after pressure testing if recommended. Conclusion: Proper installation torque is essential for Adaptor 90Â° from GZ BSPT/GZ BSP, stainless steel, type A110 to achieve reliable seals on both the BSPT thread and the 60Â° cone. Always follow the manufacturer's torque specifications and assembly instructions for the specific thread sizes and application.

Adaptor 90° from GZ BSPT/GZ BSP, stainless steel, type A110

All products, High-pressure adapters/

Additional information

Material	SS – stainless steel

90° high-pressure adapter type A110 with external BSPT thread (seal on the thread) and external BSP thread (seal on 60° cone). Material: AISI 316L steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-A110-02-SS	90° Adaptor GZ BSPT 1/8" / GZ BSP 1/8", AISI 316	-	350	In stock	Enquiry
TI-A110-04-SS	90° Adapter GZ BSPT 1/4" / GZ BSP 1/4", AISI 316	-	350	In stock	Enquiry
TI-A110-06-SS	90° Adaptor GZ BSPT 3/8" / GZ BSP 3/8", AISI 316	-	250	In stock	Enquiry
TI-A110-08-SS	90° Adapter GZ BSPT 1/2" / GZ BSP 1/2", AISI 316	-	225	In stock	Enquiry
TI-A110-12-SS	90° Adapter GZ BSPT 3/4" / GZ BSP 3/4", AISI 316	-	200	In stock	Enquiry
TI-A110-16-SS	90° Adapter GZ BSPT 1" / GZ BSP 1", AISI 316	-	160	In stock	Enquiry
TI-A110-24-SS	90° Adapter GZ BSPT 1.1/2" / GZ BSP 1.1/2", AISI 316	-	160	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

90° high-pressure adapter type A110 with external BSPT thread (seal on the thread) and external BSP thread (seal on 60° cone). Material: AISI 316L steel.