Can the Divider bar with opposite 1/8" outputs - 1/4", aluminum withstand continuous operation at the maximum 12 bar working pressure and specified temperature range?

Yes. Divider bar with opposite 1/8" outputs - 1/4", aluminum is specified for a working pressure of 12 bar and an operating temperature range of -10Â°C to +80Â°C. Made from anodized aluminum and designed for pneumatic distribution, it is intended to withstand continuous operation at the maximum stated pressure and within the given temperature limits. Ensure correct installation, secure fastening using the provided mounting holes, and use compatible fittings and seals rated for 12 bar and the temperature range to maintain safe, reliable operation.

Is the Divider bar with opposite 1/8" outputs - 1/4", aluminum compatible with standard pneumatic fittings and threads?

Divider bar with opposite 1/8" outputs - 1/4", aluminum Format: Yes - the Divider bar with opposite 1/8" outputs - 1/4", aluminum Format is designed for pneumatic systems and uses standard 1/8" and 1/4" threaded outputs common in pneumatic fittings. Made of anodized aluminum, rated for 12 bar and â10Â°C to +80Â°C, it will accept typical pneumatic fittings and can be secured via its additional mounting holes. Ensure the fittings you use match the specified thread standard (e.g., BSP or NPT) for your system, as the product description specifies port sizes but does not state the thread standard.

Does the Divider bar with opposite 1/8" outputs - 1/4", aluminum require specific mounting hardware for secure installation?

Yes. The Divider bar with opposite 1/8" outputs - 1/4", aluminum requires appropriate mounting hardware for a secure installation. The product description states it has additional holes specifically for securing it in the desired location of the installation, so you should use suitable fasteners (screws, bolts, or rivets) that match those hole sizes and the mounting surface material. Selection considerations: - Fastener type and size: choose screws/bolts that fit the divider barâs mounting holes and provide adequate shear and tensile strength for the installation. - Material compatibility: use corrosion-resistant hardware (stainless steel or zinc-plated) to avoid galvanic corrosion with the anodized aluminum body, especially in humid or corrosive environments. - Load and pressure conditions: although the bar is rated for 12 bar working pressure, mounting hardware should resist any dynamic forces from vibration or pipe stress; consider washers or lock washers and proper torque. - Temperature range: select hardware that performs reliably between â10Â°C and +80Â°C. - Sealing and isolation: where needed, use gaskets or isolation pads to prevent metal-to-metal wear and to dampen vibration. If you need exact fastener sizes or torque values, measure the mounting hole diameter on the Divider bar with opposite 1/8" outputs - 1/4", aluminum and match them to the substrate (metal, wood, or panel) or consult the manufacturer for recommended hardware.

Distribution manifold with opposite 1/8″ – 1/4″ outlets, aluminum

Accessories for pneumatic fittings, All products/

Additional information

Material	AL – aluminum

Distribution manifold with opposite 1/8″ – 1/4″ outlets for use in pneumatic systems, allowing pressurized compressed air to be split into several branches. It has additional holes for fixing it at the desired point of the installation. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: anodized aluminum.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-W0503111015	Distribution manifold dwustronna, 2 x inlet 1/4" BSP female, 6 x outlet 1/8" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503111017	Distribution manifold dwustronna, 2 x inlet 1/4" BSP female, 8 x outlet 1/8" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503111019	Distribution manifold dwustronna, 2 x inlet 1/4" BSP female, 10 x outlet 1/8" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503121016	Distribution manifold dwustronna, 2 x inlet 3/8" BSP female, 6 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503121018	Distribution manifold dwustronna, 2 x inlet 3/8" BSP female, 8 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503121020	Distribution manifold dwustronna, 2 x inlet 3/8" BSP female, 10 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503131016	Distribution manifold dwustronna, 2 x inlet 1/2" BSP female, 6 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503131018	Distribution manifold dwustronna, 2 x inlet 1/2" BSP female, 8 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0503131020	Distribution manifold dwustronna, 2 x inlet 1/2" BSP female, 10 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Distribution manifold with opposite 1/8″ – 1/4″ outlets for use in pneumatic systems, allowing pressurized compressed air to be split into several branches. It has additional holes for fixing it at the desired point of the installation. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: anodized aluminum.