Is the Rubber cover for nozzle with GW NPT compatible with all lances and 1/4" external NPT nozzles at 500 bar working pressure?

Rubber cover for nozzle with GW NPT Format is compatible with lances and nozzles that match its specified fittings and limits. Specifically: - Thread compatibility: It is designed for nozzles with external 1/4" NPT thread and for mounting on a lance with an internal NPT thread. If your lance/nozzle assembly uses 1/4" external NPT and mates with an internal NPT of the same size and thread standard, the cover will fit. - Pressure rating: The cover assembly is rated for a working pressure of 500 bar. Use within this pressure limit is acceptable. - Mechanical fit and materials: The coverâs synthetic rubber body and stainless-steel connection are intended to protect delicate surfaces and withstand typical use. However, compatibility with âall lancesâ depends on each lanceâs external dimensions, thread conformity, and any intervening adapters. Some lances or nozzles may have nonstandard thread tolerances, protruding features, or require a different NPT size. Conclusion: Rubber cover for nozzle with GW NPT Format is compatible when the nozzle has an external 1/4" NPT thread and the lance accepts an internal 1/4" NPT, and when system pressure does not exceed 500 bar. Verify thread standard/tolerance and physical clearance on your specific lance/nozzle before use.

Can the Rubber cover for nozzle with GW NPT withstand chemicals commonly used in pressure washing at 500 bar?

Rubber cover for nozzle with GW NPT Format: Synthetic rubber covers resist many common pressure-washing detergents (alkaline cleaners, mild acids, surfactants), and the stainless-steel connection tolerates corrosive exposure. However, compatibility at 500 bar depends on the exact chemical composition and temperature: strong acids, strong alkalis, solvents (ketones, aromatics), oxidizers or concentrated caustics can degrade synthetic rubbers, causing swelling, hardening or failure. For safe use at 500 bar, verify the rubber compoundâs chemical resistance against the specific agents and concentrations you use, or consult the manufacturer for a certified chemical compatibility list. If uncertain, test with the intended chemical at working pressure and temperature before regular use.

How do I install the Rubber cover for nozzle with GW NPT onto a lance with a 1/4" external NPT thread?

To install the Rubber cover for nozzle with GW NPT onto a lance with a 1/4" external NPT thread, follow these steps: 1. Ensure safety: depressurize and disconnect the lance from the pump. Wear gloves and eye protection. 2. Inspect threads: clean both the lanceâs 1/4" external NPT thread and the coverâs internal stainless steel connection. Remove dirt, debris, and old sealant. 3. Apply sealant if needed: for a pressure application up to 500 bar, use PTFE tape or a suitable thread sealant rated for high pressure on the lanceâs external thread. Wrap PTFE tape clockwise (2â3 turns) so it wonât unwind when screwing on the cover. 4. Align and hand-tighten: position the Rubber cover for nozzle with GW NPT over the lanceâs thread and engage the stainless steel connection by hand. Start threading carefully to avoid cross-threading. 5. Final tightening: hand-tighten firmly. If a wrench is required, use a suitable tool on the stainless steel connection only, applying moderate forceâdo not over-tighten, as the rubber cover must seat without distortion. 6. Inspect fit and test: ensure the rubber skirt fully covers the nozzle and sits flush to protect delicate surfaces. Re-pressurize the system slowly and check for leaks. If leakage occurs, depressurize, disassemble, reapply sealant, and retighten. Notes: The cover is designed for nozzles with a 1/4" external NPT thread and rated to 500 bar. Avoid excessive mechanical force on the rubber portion; tighten via the stainless steel connection.

Rubber cover for nozzle with GW NPT

Additional information

Material	P – material (plastic)

Rubber cover for nozzle with internal NPT thread for mounting on lance, protecting delicate cleaning surfaces from scratches. Designed for nozzle with external 1/4″ NPT thread. Cover material: synthetic rubber. Connection material: stainless steel. Working pressure: 500 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MH-220130	Nozzle cover with 1/4" NPT thread, blue	-	-	In stock	Enquiry
MH-220134	Nozzle cover with 1/8" NPT thread, black	-	-	In stock	Enquiry
MH-220278	Nozzle cover with 1/4" NPT thread, black	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Rubber cover for nozzle with internal NPT thread for mounting on lance, protecting delicate cleaning surfaces from scratches. Designed for nozzle with external 1/4″ NPT thread. Cover material: synthetic rubber. Connection material: stainless steel. Working pressure: 500 bar.