Is the Two-part long adapter for high-pressure cleaning equipment, brass compatible with M22x1.5 fittings and sealed with O-rings on both sides for use up to 280 bar and +160Â°C?

Yes. The Two-part long adapter for high-pressure cleaning equipment, brass is compatible with M22x1.5 fittings, has O-rings on both sides, and is rated for working pressures up to 280 bar and operating temperatures up to +160Â°C, per the provided specifications.

Can the Two-part long adapter for high-pressure cleaning equipment, brass be used with different O-ring materials for extreme temperatures?

Two-part long adapter for high-pressure cleaning equipment, brass as described comes with O-rings on both sides and is rated for operating temperatures up to +160Â°C. Whether it can be used with different O-ring materials for extreme temperatures depends on the specific O-ring compound you fit: the brass adapter itself is suitable, but standard O-rings supplied may limit temperature range. For extreme heat (above +160Â°C) or extreme cold, you must choose compatible elastomers (e.g., FFKM/Kalrez or metallic seals for very high temperatures; FKM/Viton for high heat up to ~200Â°C short-term; PTFE or perfluoroelastomers for broader ranges; EPDM/CR for low temperatures down to about -50Â°C to -60Â°C). Also verify chemical compatibility with cleaning agents, pressure rating at temperature, and correct O-ring dimensions for the M22x1.5 connections.

Can the Two-part long adapter for high-pressure cleaning equipment, brass be torque-tightened to prevent leaks at 280 bar?

Yes. the Two-part long adapter for high-pressure cleaning equipment, brass can be torque-tightened to help prevent leaks at 280 bar, but several important conditions must be met: - Thread and fitting type: The product uses a metric M22x1.5 connection; proper mating components with the same thread spec and clean, undamaged threads are required to ensure a correct mechanical seal when tightened. - Oârings are primary seals: This adapter has O-rings on both sides. These elastomer seals are designed to provide sealing at high pressure when compressed correctly. Torque-tightening helps compress the O-rings uniformly but should not be used to replace a missing or damaged Oâring. - Correct torque and procedure: Overâ or underâtorquing can cause leaks, Oâring extrusion or thread damage. Use manufacturerârecommended torque values for M22x1.5 fittings or follow your equipmentâs service manual. If no specific torque is given, consult a qualified technician or use calibrated tools and tighten progressively to achieve a secure, even fit. - Material and pressure rating: The adapter is brass and rated for working pressure up to 280 bar and temperatures up to +160Â°C, so when installed correctly with intact Oârings and compatible mating parts, it is suitable for use at 280 bar. - Install considerations: Ensure Oârings are correct material for fluid/temperature, lubricated per recommendations, free of nicks, and properly seated. Inspect threads for debris or damage and avoid thread sealants that could interfere with Oâring sealing unless manufacturer permits. - Safety: After installation, perform a controlled pressure test and check for leaks before full operation. Replace Oârings periodically and immediately if any leakage or degradation appears. In short: Yes, torque-tightening the Two-part long adapter for high-pressure cleaning equipment, brass can prevent leaks at 280 bar when done with correct mating parts, intact and compatible Oârings, proper torque and installation practices.

Two-part long adapter for high-pressure cleaning equipment, brass

Additional information

Material	B – brass (bronze)

Two-part long adapter for high-pressure cleaning devices with metric connection M22x1.5. With O-ring on both sides of the connection. Material: brass. Working pressure: up to 280 bar. Operating temperature: up to +160°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
MH-240035	Adapter 2 pcs. GW M22x1.5, long / GW 1/4	-	280	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Two-part long adapter for high-pressure cleaning devices with metric connection M22x1.5. With O-ring on both sides of the connection. Material: brass. Working pressure: up to 280 bar. Operating temperature: up to +160°C.