Can ORFS 45Â° hydraulic end, type ZOW310, carbon steel withstand typical hydraulic system pressures and temperatures for industrial hose assemblies?

ORFS 45Â° hydraulic end, type ZOW310, carbon steel Format can withstand typical hydraulic system pressures and temperatures for industrial hose assemblies when used as intended. Its ORFS flat sealing and 45Â° Z-type tail with internal UNF thread and nut are standard for high-pressure hydraulic connections, and carbon steel with galvanization provides good strength and corrosion resistance. Critical factors: match the fitting size to the hose and crimping sleeve specified for that hose, use correct crimping parameters and tooling, and ensure compatibility with the hydraulic fluid and operating temperature range. If system pressures/temperatures exceed the hose, fitting, or crimp spec, or if aggressive fluids are used, consult manufacturer specifications or certified test data before service.

What crimping sleeve sizes and hose types are recommended for ORFS 45Â° hydraulic end, type ZOW310, carbon steel?

For ORFS 45Â° hydraulic end, type ZOW310, carbon steel, select crimping sleeves sized to match the hose I.D. and construction. Recommendations: - Common hose types: single-wire braid, two-wire braid, textile braid, and spiral (4- or 6-wire) hydraulic hoses. ZOW310 is suitable for hoses designed for mechanical crimping. - Sleeve material: carbon steel, zincâplated or galvanized to match fitting corrosion resistance. - Sleeve profile: standard hex/long ferrule compatible with ORFS crimp style; use manufacturer-specific ferrules when available. - Sleeve sizes by typical hose I.D. (choose the sleeve whose internal bore equals the hose outer diameter): - For 1/4" hose (6 mm I.D. / ~8â9 mm O.D.) â use sleeve for 1/4" hose - For 3/8" hose (10 mm I.D. / ~12â13 mm O.D.) â use sleeve for 3/8" hose - For 1/2" hose (13 mm I.D. / ~16â17 mm O.D.) â use sleeve for 1/2" hose - For 3/4" hose (19 mm I.D. / ~22â24 mm O.D.) â use sleeve for 3/4" hose - For 1" hose (25 mm I.D. / ~28â30 mm O.D.) â use sleeve for 1" hose - Crimp dimensions and die set: follow hose and sleeve manufacturersâ crimp diameter and crimp length specifications; use the die set matched to the sleeve size and hose construction (single-wire vs. spiral requires different crimping force and die profile). - Seal and thread: ensure ORFS flat face seals properly; the sleeve must allow correct insertion depth so the fittingâs UNF thread and nut can engage without disturbing the sealing face. - Quality checks: after crimping inspect crimp profile, measure crimp diameter, perform pressure test per hose/fitting spec. If you have the exact hose series and O.D./I.D., provide that for precise sleeve part numbers and crimp diameters.

ORFS 45° hydraulic end, type ZOW310, carbon steel

Q: Is the ORFS 45Â° hydraulic end, type ZOW310, carbon steel compatible with standard UNF-threaded hoses and crimping sleeves for industrial hydraulic applications?

Yes. The ORFS 45Â° hydraulic end, type ZOW310, carbon steel is compatible with standard UNF-threaded hoses and crimping sleeves intended for industrial hydraulic use. Rationale based on the provided description: - It has an internal UNF thread and nut, so it mates with hoses or adapters using UNF thread standards. - It features ORFS flat sealing at 45Â°, which is the standard face-sealing geometry for ORFS fittings and seals properly against ORFS-matched ports or hose fittings. - It is explicitly designed for crimping in hydraulic and industrial hoses and requires a crimping sleeve suitable for the specific hose type.so using the correct sleeve for your hose will allow proper crimping. - Material (carbon steel, galvanized) is typical for industrial hydraulic fittings and compatible with standard hose assemblies when proper crimping procedures and sleeve materials are used. Ensure you use the correct UNF thread size, an ORFS-compatible mating component, and a crimping sleeve specified for your hose construction and pressure rating.

All products, Fittings for high-pressure hoses/

ORFS 45° hydraulic end, type ZOW310, carbon steel

Additional information

Material	CS – steel (cast iron)

Standard hydraulic end (type Z – with a regular hydraulic “tail” for hose), with internal UNF thread and nut, flat sealing (ORFS), 45° angle. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZOW310-09-04	End. ORFS 45° G 9/16", hose 1/4"	6	-	In stock	Enquiry
TI-ZOW310-09-05	End. ORFS 45° G 9/16", hose 5/16"	8	-	In stock	Enquiry
TI-ZOW310-09-06	End. ORFS 45° G 9/16", hose 3/8"	10	-	In stock	Enquiry
TI-ZOW310-11-04	End. ORFS 45° G 11/16", hose 1/4"	6	-	In stock	Enquiry
TI-ZOW310-11-05	End. ORFS 45° G 11/16", hose 5/16"	8	-	In stock	Enquiry
TI-ZOW310-11-06	End. ORFS 45° G 11/16", hose 3/8"	10	-	In stock	Enquiry
TI-ZOW310-13-06	End. ORFS 45° G 13/16", hose 3/8"	10	-	In stock	Enquiry
TI-ZOW310-13-08	End. ORFS 45° G 13/16", hose 1/2"	12	-	In stock	Enquiry
TI-ZOW310-16-08	End. ORFS 45° G1" hose 1/2"	12	-	In stock	Enquiry
TI-ZOW310-16-10	End. ORFS 45° G1", hose 5/8"	16	-	In stock	Enquiry
TI-ZOW310-19-10	End. ORFS 45° G1/4", hose 5/8"	16	-	In stock	Enquiry
TI-ZOW310-19-12	End. ORFS 45° G1/4", hose 3/4"	20	-	In stock	Enquiry
TI-ZOW310-23-12	End. ORFS 45° G1.7/16", hose 3/4"	20	-	In stock	Enquiry
TI-ZOW310-23-16	End. ORFS 45° G1.7/16", hose 1"	25	-	In stock	Enquiry
TI-ZOW310-27-20	End. ORFS 45° G1.11/16", hose 1.1/4"	32	-	In stock	Enquiry
TI-ZOW310-32-24	End. ORFS 45° G 2", hose 1.1/2"	38	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Standard hydraulic end (type Z – with a regular hydraulic “tail” for hose), with internal UNF thread and nut, flat sealing (ORFS), 45° angle. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.