Is the Screw for BANJO inch, steel AISI 316L compatible with standard inch banjo fittings and does it require a washer?

Screw for BANJO inch, steel AISI 316L . compatibility and washer requirement Yes . the Screw for BANJO inch, steel AISI 316L is designed for Banjo type Z with an inch thread, so it is compatible with standard inch banjo fittings that use the same Banjo type Z specification. According to the description (âBanjo type Z, inch screw without washerâ), this screw is supplied without a washer. If your application or the mating banjo fitting requires a sealing washer (common for fluid or pressure connections), you will need to provide the correct washer separately.ensure it matches the screw diameter, thickness and material/chemical compatibility for a proper seal. If the banjo assembly or manufacturer documentation specifies a crush washer or sealing type, use that specification to select the washer.

Can the Screw for BANJO inch, steel AISI 316L be used in high-pressure sanitary systems without a washer?

Screw for BANJO inch, steel AISI 316L Format: No - using the Screw for BANJO inch, steel AISI 316L without a washer is not recommended for high-pressure sanitary systems. The washer (typically an elastomeric or metal gasket) provides sealing, load distribution and vibration resistance; omitting it risks leaks, flange damage and loss of pressure integrity. For AISI 316L material the screw offers corrosion resistance, but sealing performance depends on the correct washer type and installation torque. Always follow manufacturer specifications and applicable sanitary pressureâsystem standards; if a washerless configuration is required, confirm with the supplier/engineer and use a design explicitly certified for washerless highâpressure sanitary use.

Does the Screw for BANJO inch, steel AISI 316L provide sufficient sealing and corrosion resistance without a washer?

Screw for BANJO inch, steel AISI 316L made as an inch screw without a washer (Banjo type Z) can provide acceptable sealing and good corrosion resistance in certain conditions, but there are important caveats. Sealing: - Without a washer, the seal depends on metal-to-metal contact between the screw head/seat and the mating surface and on thread engagement. AISI 316L is ductile and can deform slightly to improve contact, but it is not a dedicated sealing material. For reliable, pressure-tight sealingâespecially with fluids, gases, cyclic pressure, or higher pressuresâa compressible gasket (washer) or an Oâring is normally recommended. - For low-pressure, non-critical applications or where the mating flange/face is machined to a high surface finish and clamping torque is properly controlled, the screw alone can often provide a leakâfree joint. However, factors such as vibration, temperature cycling, and imperfect surfaces increase the risk of leakage without a washer. Corrosion resistance: - Screw for BANJO inch, steel AISI 316L offers excellent general corrosion resistance, including good resistance to chloride-induced corrosion compared to lower-grade stainless steels. It performs well in many marine, chemical, and sanitary environments. - Corrosion resistance at the sealing interface depends on the mating material. Dissimilar metals, crevices, or trapped fluids can promote localized corrosion (crevice corrosion). Without a washer that isolates surfaces or selects compatible materials, there may be greater risk in aggressive environments. Summary recommendation: - For critical sealing, pressurized systems, or aggressive media: do not rely solely on Screw for BANJO inch, steel AISI 316L without a proper washer or gasket. - For low-pressure, non-critical, wellâmachined joints in benign environments, the screw alone may suffice, but ensure correct torque and inspect periodically. - When in doubt, use a suitable washer/gasket of compatible material to ensure reliable sealing and reduce corrosion risk.

Screw for BANJO inch, steel AISI 316L

All products, Fittings for high-pressure hoses/

Additional information

Banjo type Z, inch screw without washer. Material: AISI 316L steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZBB610-04-SS	Banjo screw 1/4", AISI 316L	-	-	In stock	Enquiry
TI-ZBB610-06-SS	Banjo bolt 3/8", AISI 316L	-	-	In stock	Enquiry
TI-ZBB610-06-SS-PH	Banjo bolt 3/8", AISI 316L	-	-	In stock	Enquiry
TI-ZBB610-08-SS	Banjo bolt 1/2", AISI 316L	-	-	In stock	Enquiry
TI-ZBB610-12-SS	Banjo bolt 3/4", AISI 316L	-	-	In stock	Enquiry
TI-ZBB610-16-SS	1" BANJO screw, AISI 316L	-	-	In stock	Enquiry