Is the High-pressure washer nozzle, stainless steel, type ZKW110 compatible with standard threaded high-pressure washer hoses and adapters?

Based on the provided description . "Internal threaded end for high-pressure washers. Material: stainless steel." . the High-pressure washer nozzle, stainless steel, type ZKW110 is designed with an internal (female) thread meant to accept a matching externally threaded (male) high-pressure washer hose or adapter. Compatibility therefore depends on matching the thread type and size: - If your hose or adapter uses the same standard thread type and size as the ZKW110 (commonly used standards are M22Ã1.5 or BSP/UNF variants depending on region/manufacturer), the nozzle will be compatible and can be screwed directly onto the hose/adapter. - If the hose/adapter uses a different thread standard or size, you will need a suitable adapter or converter to achieve compatibility. Because the description does not specify the exact thread standard/diameter, confirm the thread specification of both the ZKW110 and your hose/adapter (or consult the supplier) before purchase to ensure a correct fit.

Does the High-pressure washer nozzle, stainless steel, type ZKW110 have an internal thread size specification for compatibility?

High-pressure washer nozzle, stainless steel, type ZKW110: The description states an "Internal threaded end for high-pressure washers" and material stainless steel, but it does not specify the internal thread size. Therefore, based on the provided description alone, there is no listed internal thread size specification for compatibility. To confirm compatibility with a specific washer, request the exact thread dimensions (e.g., thread type, diameter and pitch) from the seller or manufacturer.

High-pressure washer nozzle, stainless steel, type ZKW110

Q: What maintenance is required for the High-pressure washer nozzle, stainless steel, type ZKW110 to prevent thread corrosion?

To prevent thread corrosion for the High-pressure washer nozzle, stainless steel, type ZKW110, follow these maintenance steps: 1. Regular inspection - Check threads for pitting, discoloration or buildup after each use or at least weekly with frequent use. - Inspect O-rings/seals and surrounding fittings for wear or damage. 2. Cleaning - Rinse threads with fresh water after use, especially after exposure to salt water, chlorine or harsh chemicals. - Use a soft brush and mild detergent to remove deposits; avoid abrasive tools that can damage stainless steel surface. - Dry threads thoroughly with a clean cloth to prevent moisture retention. 3. Preventing galvanic corrosion - Avoid direct contact with dissimilar metals (e.g., copper, brass, carbon steel) without an insulating barrier. - Use non-conductive thread tape (PTFE) or a compatible anti-seize designed for stainless steel to isolate metals and reduce galling. 4. Lubrication and anti-seize - Apply a thin layer of stainless-steel-compatible anti-seize compound to threads periodically (especially if disassembling/reassembling frequently or when exposed to corrosive environments). - For light maintenance, use a corrosion-inhibiting lubricant suitable for stainless steel threads. 5. Proper storage - Store nozzle dry in a ventilated, low-humidity environment. - Keep away from corrosive chemicals and salt-laden air when not in use. 6. Handling - Tighten to recommended torqueâavoid over-tightening which can damage threads and protective passive layer. - When assembling, ensure threads are clean and free of debris to prevent cross-threading and surface damage. 7. Replacement - Replace the nozzle if threads show deep corrosion, irreversible pitting, or if sealing is compromised. Following these steps will help preserve the passive protective layer of the stainless steel and minimize thread corrosion on the High-pressure washer nozzle, stainless steel, type ZKW110.

Additional information

Material	SS – stainless steel
Standard length [m]	2

Internal threaded end for high-pressure washers. Material: stainless steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZKW110-22-04-SS	End. KARCHER GW M22x1.5, hose 1/4", AISI 316	6	-	In stock	Enquiry
TI-ZKW110-22-05-SS	End. KARCHER GW M22x1.5, hose 5/16", AISI 316	8	-	In stock	Enquiry
TI-ZKW110-22-06-SS	End. KARCHER GW M22x1.5, hose 3/8", AISI 316	10	-	In stock	Enquiry
TI-ZKW110-22-08-SS	End. KARCHER GW M22x1.5, hose 1/2", AISI 316	12	-	In stock	Enquiry