Is the BANJO metric RNM hydraulic end, type SMB600, carbon steel compatible with standard rubber and thermoplastic hoses when using a screwed sleeve?

Yes. The BANJO metric RNM hydraulic end, type SMB600, carbon steel is compatible with standard rubber and thermoplastic hoses when used with a screwed sleeve. The product description explicitly states it is designed for screwing into rubber and thermoplastic hoses using a screwed sleeve, and the carbon steel, galvanized construction is typical for such hose terminations, providing the necessary mechanical strength and corrosion resistance for standard hydraulic applications. Ensure you match the metric thread size RNM and sleeve dimensions to the hose I.D./wall and operating pressure ratings to guarantee a proper, secure assembly.

Can BANJO metric RNM hydraulic end, type SMB600, carbon steel be used with hoses of different inner diameters when fitted with a screwed sleeve?

Yes - BANJO metric RNM hydraulic end, type SMB600, carbon steel can be used with hoses of different inner diameters only if the matching screwed sleeve (ferrule) and hose are correctly sized and compatible. The RNM/SMB600 end is designed for rubber and thermoplastic hoses secured with a screwed sleeve; proper sealing and mechanical integrity require the sleeve, hose OD/ID, and fitting bore to match the manufacturerâs specified hose size range. Using an incorrectly sized sleeve or mismatched ID may cause leaks, reduced crimp retention, or failure. Always verify the exact hose inner diameter, wall thickness, and sleeve part number against BANJOâs specifications or consult their technical data before assembly.

Does BANJO metric RNM hydraulic end, type SMB600, carbon steel require specific torque specs when tightened with a screwed sleeve?

Yes. BANJO metric RNM hydraulic end, type SMB600, carbon steel requires specific torque control when tightened with a screwed sleeve. Explanation: Although the product description (Hydraulic screw end, type S, BANJO for a screw with metric thread (RNM). Designed for screwing in rubber and thermoplastic hoses using a screwed sleeve. Material: carbon steel, galvanized) does not list numeric torque values, proper assembly practice for metric RNM screw ends with a screwed sleeve mandates controlled torque to ensure sealing, hose retention, and to avoid damage to threads or deformation of the sleeve/hose. Torque requirements depend on several factors: thread size/pitch of the RNM fitting, diameter and type of the hose (rubber vs thermoplastic), sleeve material and thickness, lubrication or plating (galvanized surface), and use of washers/seals. Recommended actions: - Consult the manufacturerâs assembly datasheet or BANJO technical literature for SMB600/RNM torque charts. Manufacturers typically publish recommended torque ranges by thread size. - If manufacturer data is unavailable, use industry-standard tightening procedures for metric hydraulic screw fittings (start with conservative torque values for the given nominal thread and verify by functional test). Example practice: hand-tighten, then apply specified additional wrench turns or a torque consistent with comparable metric fittings of the same size (do not overtighten). - Use calibrated torque tools and re-check after initial pressurization/cycling. - Inspect for proper crimp/compression of the sleeve and absence of thread damage or hose distortion. - If critical application, contact BANJO or supplier technical support for exact torque specification for SMB600. Without the explicit torque number in the provided description, do not assume a generic torque; obtain the manufacturerâs specified torque for safe and reliable assembly.

BANJO metric RNM hydraulic end, type SMB600, carbon steel

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)
Standard length [m]	2

Hydraulic screw end, type S, BANJO for a screw with metric thread (RNM). Designed for screwing in rubber and thermoplastic hoses using a screwed sleeve. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-SMB600-10-025	BANJO fitting M10, hose 5/32	4	-	In stock	Enquiry
TI-SMB600-10-03	BANJO fitting M10, hose 3/16	5	-	In stock	Enquiry
TI-SMB600-10-04	BANJO fitting M10, hose 1/4"	6	-	In stock	Enquiry
TI-SMB600-12-04	BANJO fitting M12, hose 1/4"	6	-	In stock	Enquiry
TI-SMB600-16-05	BANJO fitting M16, hose 5/16"	8	-	In stock	Enquiry
TI-SMB600-18-05	BANJO fitting M18, hose 5/16"	8	-	In stock	Enquiry
TI-SMB600-18-06	BANJO fitting M18, hose 3/8"	10	-	In stock	Enquiry
TI-SMB600-18-08	BANJO fitting M18 hose 1/2"	12	-	In stock	Enquiry
TI-SMB600-20-06	BANJO M20 fitting 3/8" hose	10	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Hydraulic screw end, type S, BANJO for a screw with metric thread (RNM). Designed for screwing in rubber and thermoplastic hoses using a screwed sleeve. Material: carbon steel, galvanized.