Can GZ BSPT twisted hydraulic end, carbon steel, AGR-K type S withstand high-pressure applications in rubber and thermoplastic hoses?

Yes. The GZ BSPT twisted hydraulic end, carbon steel, AGR-K type S is designed for screwing into rubber and thermoplastic hoses with a screwed sleeve and features an external BSPT thread with a 60Â° sealing cone on the thread (AGR-K). Made of carbon steel and galvanized, it provides the mechanical strength and corrosion resistance typical for high-pressure hydraulic fittings. Proper installation with the matching sleeve, correct hose type, and following manufacturer torque and pressure ratings is required to ensure safe high-pressure performance. Always verify the specific working pressure rating and compatibility with your hose and fluid before use.

How do I correctly install the GZ BSPT twisted hydraulic end, carbon steel, AGR-K type S into a screwed sleeve?

To correctly install the GZ BSPT twisted hydraulic end, carbon steel, AGR-K type S into a screwed sleeve, follow these steps: 1. Inspect components: ensure GZ BSPT twisted hydraulic end, screwed sleeve and hose are clean, undamaged and match in size/specification (external BSPT thread, 60Â° sealing cone). Check sleeve for correct internal thread and chamfer. 2. Prepare hose: cut hose squarely, remove burrs, and ensure inner bore is clean. For rubber or thermoplastic hoses, check reinforcement is intact and free of fraying. 3. Insert ferrule/sleeve: slide the screwed sleeve over the hose end, oriented so the threaded end faces outward for assembly. 4. Fit tailpiece: push the GZ BSPT twisted hydraulic end fully into the hose until the hose meets the tailpiece shoulder. Ensure the 60Â° cone aligns with the hose end and that the hose covers any barbs or gripping features as specified by the manufacturer. 5. Engage sleeve: bring the screwed sleeve forward over the hose onto the tailpiece so that threads engage. Make sure the sleeve aligns straight and does not cross-thread. 6. Tighten: hand-start the sleeve on the GZ BSPT twisted hydraulic end, then use appropriate wrenches to tighten to the manufacturerâs recommended torque or number of turns past hand-tight for BSPT fittings. Ensure the 60Â° sealing cone seats properlyâdo not over-tighten to avoid damaging threads or deforming the cone. 7. Check orientation: since the fitting is twisted type, verify final rotation/position is as required for hose routing before final torqueing. 8. Inspect and test: visually inspect the joint for proper engagement, correct sleeve position and no exposed reinforcement. Perform pressure testing per system requirements to check for leaks. 9. Re-tighten if needed: after initial pressure test, recheck torque and retest. Use appropriate personal protective equipment and follow hydraulic safety procedures. If manufacturer-specific torque or assembly instructions exist for the GZ BSPT twisted hydraulic end, carbon steel, AGR-K type S, follow them exactly.

GZ BSPT twisted hydraulic end, carbon steel, AGR-K type S

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)

Screwed hydraulic end, type S, with external BSPT thread, sealing cone 60° / on the thread (AGR-K). Designed for screwing into rubber and thermoplastic hoses using a screwed sleeve. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-SBZ130-02-03	End screw GZ BSPT 1/8", hose 5/16"	-	-	In stock	Enquiry
TI-SBZ130-04-04	End screw GZ BSPT 1/4", hose 1/4"	-	-	In stock	Enquiry
TI-SBZ130-06-05	End screw GZ BSPT 3/8", hose 5/16"	-	-	In stock	Enquiry
TI-SBZ130-06-06	End screw GZ BSPT 3/8", hose 3/8"	-	-	In stock	Enquiry
TI-SBZ130-08-08	End screw GZ BSPT 1/2", hose 1/2"	-	-	In stock	Enquiry
TI-SBZ130-12-10	End screw GZ BSPT 3/4", hose 5/8"	-	-	In stock	Enquiry
TI-SBZ130-12-12	End screw GZ BSPT 3/4", hose 3/4"	-	-	In stock	Enquiry
TI-SBZ130-16-16	End screw GZ BSPT 1", hose 1"	-	-	In stock	Enquiry
TI-SBZ130-20-20	End screw GZ BSPT 1.1/4", hose 1.1/4"	-	-	In stock	Enquiry
TI-SBZ130-24-24	End screw GZ BSPT 1.1/2", hose 1.1/2"	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Screwed hydraulic end, type S, with external BSPT thread, sealing cone 60° / on the thread (AGR-K). Designed for screwing into rubber and thermoplastic hoses using a screwed sleeve. Material: carbon steel, galvanized.