Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality, strong two-part steel clamp for high dynamic loads with DÄMMGULAST® anti-vibration insert and two locking screws secured with plastic washers to prevent falling out during tightening. The screws allow for adjustment to accommodate larger changes in pipe diameter. The anti-vibration insert with a yellow identification stripe (average sound level improvement of up to 22 dB(A)) is made of water-resistant, abrasion-resistant, temperature-resistant, and aging-resistant EPDM rubber. A two-stage head with M8/M10 thread size is welded onto one part of the clamp. The clamp is designed for installation in vertical, horizontal, or suspended arrangements for all types of pipes: steel, cast iron, copper, plastic. A proven solution in water and sewage installations, during the construction of heating, gas, ventilation, air conditioning systems, in residential and industrial buildings. The clamp is distinguished by the quality mark "Gütezeichen Rohrbefestigung" for sizes ≤200 mm and is subject to inspection according to the RAL-GZ 655-B instruction. Products with the RAL quality mark must fully meet the stringent requirements in accordance with the standards contained in RAL GZ 655. The clamp is tested for fire safety for sizes ≤170 mm (RAL-GZ 656). Clamp material: AISI 304 steel (W4) or AISI 316 steel (W5). Insert material: EPDM.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality, strong two-part steel clamp for high dynamic loads with DÄMMGULAST® anti-vibration insert and two locking screws secured with plastic washers to prevent falling out during tightening. The screws allow for adjustment to accommodate larger changes in pipe diameter. The anti-vibration insert with a yellow identification stripe (average sound level improvement of up to 22 dB(A)) is made of water-resistant, abrasion-resistant, temperature-resistant, and aging-resistant EPDM rubber. A two-stage head with M8/M10 thread size is welded onto one part of the clamp. The clamp is designed for installation in vertical, horizontal, or suspended arrangements for all types of pipes: steel, cast iron, copper, plastic. A proven solution in water and sewage installations, during the construction of heating, gas, ventilation, air conditioning systems, in residential and industrial buildings. The clamp is distinguished by the quality mark "Gütezeichen Rohrbefestigung" for sizes ≤200 mm and is subject to inspection according to the RAL-GZ 655-B instruction. Products with the RAL quality mark must fully meet the stringent requirements in accordance with the standards contained in RAL GZ 655. The clamp is tested for fire safety for sizes ≤170 mm (RAL-GZ 656). Clamp material: carbon steel, galvanized (W1). Insert material: EPDM.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for the safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation pipes (hose covers), etc., where there is a risk of abrasion and damage. This type of clamp has a wide range of applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of AISI 304 stainless steel (W4), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The W4 version is recommended for marine industry applications. The clamp does not include a screw, washer, or nut. Material: AISI 304 steel (strip), EPDM rubber (flange). Strip width: 15 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation pipes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber collar. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of galvanized carbon steel (W1), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The clamp does not include a screw, washer, or nut. Material: galvanized carbon steel (strip), EPDM rubber (collar). Strip width: 12 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation tubes (hose covers), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of galvanized carbon steel (W1), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The clamp does not include a screw, washer, or nut. Material: galvanized carbon steel (strip), EPDM rubber (flange). Strip width: 15 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for the safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation tubes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of AISI 304 stainless steel (W4), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The W4 version is recommended for marine industry applications. The clamp does not include a screw, washer, or nut. Material: AISI 304 steel (strip), EPDM rubber (flange). Strip width: 20 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for the safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation tubes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of AISI 304 stainless steel (W4), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The W4 version is recommended for marine industry applications. The clamp does not include a screw, washer, or nut. Material: AISI 304 steel (strip), EPDM rubber (flange). Strip width: 12 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for safe and vibration-damping mounting of pipes, hoses, hose bundles, corrugated electrical installation pipes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of galvanized carbon steel (W1), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The clamp does not include a screw, washer, or nut. Material: galvanized carbon steel (strip), EPDM rubber (flange). Strip width: 20 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial double clamp with varying diameter for pipes, hoses, and flexible conduits, for light applications, with practical screw mounting (mounting screw not included - must be ordered separately). Material: polypropylene.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsOne-piece EXHAUST clamp with a screw has been designed for the automotive industry and is used for securely connecting exhaust pipes to mufflers exposed to high temperatures and vibrations. The clamp's design ensures the maintenance of grip and sealing around the entire circumference of the pipes, which helps prevent exhaust leaks. The rounded edges of the clamp protect the surfaces of the pipes from damage. Material: carbon steel, galvanized (W1).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for the safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation tubes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has a wide range of applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of AISI 304 stainless steel (W4), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The W4 version is recommended for use in the marine industry. The clamp does not include a screw, washer, or nut. Material: AISI 304 steel (strip), EPDM rubber (flange). Strip width: 25 mm.
