Is the Twisted coupling for pneumatic hoses angle 90Â° with external thread, type C5/C suitable for soft plastic hoses and rated for 18 bar working pressure?

Yes. The Twisted coupling for pneumatic hoses angle 90Â° with external thread, type C5/C is suitable for soft plastic hoses and is rated for a working pressure of 18 bar. It connects by pushing the hose onto the fitting and securing it by screwing on the nut, and is made of nickel-plated brass.

Can the Twisted coupling for pneumatic hoses angle 90Â° with external thread, type C5/C be tightened by hand when used with soft plastic hoses rated 18 bar?

Yes - the Twisted coupling for pneumatic hoses angle 90Â° with external thread, type C5/C can be tightened by hand when used with soft plastic hoses rated 18 bar. The design specifies connection by pushing the hose onto the fitting and tightening the nut; with soft plastic hoses and the nickel-plated brass construction, hand tightening will generally provide a secure seal up to the stated working pressure of 18 bar. For maximum safety and leak prevention, ensure the hose is fully seated, the nut is firmly hand-tightened, and verify under pressure; if repeated high-pressure cycles or critical applications are expected, a final check with a suitable tool or clamp is recommended.

Does the Twisted coupling for pneumatic hoses angle 90Â° with external thread, type C5/C require a torque wrench for secure tightening on soft plastic hoses?

Twisted coupling for pneumatic hoses angle 90Â° with external thread, type C5/C does not strictly require a torque wrench for secure tightening on soft plastic hoses. The designâpush-on hose fitting with a nut that is screwed onâallows for manual tightening to create a secure connection. However, because the hoses are made of soft plastics, care is needed: overtightening can damage or deform the hose, while undertightening can cause leaks or slippage at pressures up to the specified 18 bar. Recommended practice: - Hand-tighten the nut firmly, then use a spanner for a fraction of a turn if necessary to ensure a leak-proof fit. - Avoid excessive torque; follow any manufacturer torque guidance if provided. - Consider using a hose clamp or appropriate ferrule if repeated disconnections, high vibration, or maximum-pressure operation is expected. - After initial installation, pressurize the system and inspect for leaks; retighten gently if required. In critical applications or where consistent, repeatable tightening is needed, using a torque wrench set to the manufacturerâs recommended value (if available) is advisable to prevent under- or overtightening.

Screw-together fitting for pneumatic hoses, 90° angled, with male thread, type C5/C

All products, Tubular fittings/

Additional information

Material	B – brass (bronze)

Push-on 90° angled coupling with male thread, type C5/C, designed for connecting hoses made of soft plastics. The connection is made by pushing the hose onto the fitting and clamping it by tightening the nut. Material: nickel-plated brass. Working pressure: 18 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
MW-2357001	Angled fitting (elbow) C5/C, hose 6/4, M12x1.5 male	-	16	In stock	0 zł		Enquiry
MW-2357002	Angled fitting (elbow) C5/C, hose 8/6, M12x1.5 male	-	16	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Push-on 90° angled coupling with male thread, type C5/C, designed for connecting hoses made of soft plastics. The connection is made by pushing the hose onto the fitting and clamping it by tightening the nut. Material: nickel-plated brass. Working pressure: 18 bar.