Can the 90Â° quick connect plug with hose nut, with valve, polypropylene, PLC series DN 6.3 withstand continuous use at 8.3 bar and 71Â°C without seal degradation?

Yes . the 90Â° quick connect plug with hose nut, with valve, polypropylene, PLC series DN 6.3 can be used continuously at 8.3 bar and 71Â°C without immediate seal degradation, provided operating conditions do not exceed the specified limits. The product specification lists a working pressure âup to 8.3 barâ and an operating temperature range âfrom 0Â°C to +71Â°C,â and the seal material is EPDM, which is generally compatible with water and many cleaning fluids and retains good sealing properties at temperatures up to ~+70â90Â°C. Important caveats: - Continuous operation at the absolute maximum rated pressure and temperature increases stress on both the polypropylene body and the EPDM Oâring; longâterm aging, creep, or accelerated wear is more likely at the limits than at lower values. - Chemical compatibility: EPDM is suitable for water and many detergents but is not resistant to certain solvents, strong oxidizers or hydrocarbons. Confirm the fluid chemistry (including any additives) is EPDMâcompatible. - Installation, dynamic loads, pressure spikes, and thermal cycling can shorten service life. Ensure proper installation, pressure surge control, and periodic inspection/replacement of Oârings as part of maintenance. Conclusion: Within the stated specification (â¤8.3 bar and â¤71Â°C) and with compatible fluids and proper installation/maintenance, continuous use is acceptable; however, for critical applications consider de-rating (lower pressure/temperature margins), verify chemical compatibility, and schedule regular inspections.

Is the 90Â° quick connect plug with hose nut, with valve, polypropylene, PLC series DN 6.3 suitable for potable deionized water systems?

Yes - the 90Â° quick connect plug with hose nut, with valve, polypropylene, PLC series DN 6.3 is suitable for potable deionized water systems with some caveats. Polypropylene body and EPDM oâring are chemically compatible with deionized water and commonly used in potable water applications. The working pressure (up to 8.3 bar) and operating temperature range (0Â°C to +71Â°C) are adequate for typical potable deionized water systems. Ensure system requirements for total dissolved solids, conductivity, and leachables are met for your specific potable water certification needs; if drinking-water regulatory certification (e.g., NSF/ANSI) is required, verify manufacturer compliance. For ultrapure or highâpurity applications, consider materials and sealing qualifications specific to that purity level.

Does the 90Â° quick connect plug with hose nut, with valve, polypropylene, PLC series DN 6.3 resist common cleaning chemicals used in deionized water systems?

Yes. the 90Â° quick connect plug with hose nut, with valve, polypropylene, PLC series DN 6.3 shows good chemical resistance to many common cleaning chemicals used in deionized (DI) water systems, but with important limits. Why it generally resists cleaning chemicals: - Body material: polypropylene is broadly resistant to acids, alkalis and many cleaning agents commonly used in DI water system maintenance (e.g., diluted acids, alkaline detergents, and many surfactants). - Sealing: the EPDM O-ring is resistant to hot and cold water, many detergents, and typical alkaline cleaners used for rinsing and sanitizing lines. - Intended use: the product description lists washing installations and deionized water filtration as target applications, indicating suitability for such environments. Limitations and cautions: - Strong oxidizers (e.g., concentrated hydrogen peroxide, strong chlorine solutions, sodium hypochlorite at high concentrations or long exposure) can attack polypropylene and EPDM over time and may degrade seals or fittings. - Solvents and aggressive organic chemicals (chlorinated solvents, ketones, aromatic hydrocarbons) are not compatible with polypropylene and can cause swelling or failure. - Temperature and pressure: compatibility depends on staying within the stated operating range (0Â°C to +71Â°C and up to 8.3 bar). Elevated temperature plus aggressive chemicals accelerates degradation. - Contact time and concentration matter: brief, dilute exposures typical in routine DI system cleaning are more likely acceptable than continuous exposure to concentrated reagents. Recommendation: For specific cleaning agents and concentrations used in your DI system, verify compatibility against polypropylene and EPDM chemical compatibility charts or consult the chemical supplier. If using strong oxidizers, high concentrations, or elevated temperatures, consider alternative materials or protective measures.

Plug 90° quick coupling with a nut na hose, with valve, polypropylene, series PLC DN 6.3

All products, Industrial plastic quick couplings/

Additional information

Material	P – material (plastic)

Medium size plug 90° quick coupling with a nut na hose, intended for installations washing, filtration water deionized, machines industrial, detection leakage, itp. Length L – total length. Material: polypropylene. Sealing: O-ring EPDM. Working pressure: for 8.3 bar. Operating temperature: from 0°C to +71°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
CC-PLV-41-PP	Plug 90° PLC DN6.4 for hose 9.5x6.4 with a nut, with a valve, polypropylene	6	8.3	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Medium size plug 90° quick coupling with a nut na hose, intended for installations washing, filtration water deionized, machines industrial, detection leakage, itp. Length L – total length. Material: polypropylene. Sealing: O-ring EPDM. Working pressure: for 8.3 bar. Operating temperature: from 0°C to +71°C.