What is the correct installation torque for Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 to ensure proper 60Â° cone sealing?

Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 requires correct installation torque to ensure proper 60Â° cone sealing without damaging threads or deforming the cone. Exact torque depends on thread size (metric nominal diameter), thread pitch, lubrication/galvanization condition and mating material. General guidance: - For clean, lightly oiled galvanised carbon steel metric threads with a 60Â° cone, use standard metric thread torque values reduced by ~10â20% to account for the cone sealing surface. - Typical torque ranges (approximate): - M12: 40â60 Nm - M16: 80â110 Nm - M20: 130â180 Nm - M24: 200â260 Nm - M27: 260â330 Nm - M30: 320â400 Nm Procedure: 1. Ensure mating 60Â° cone and threads are clean and undamaged. 2. Apply light machine oil to threads (unless manufacturer specifies dry). 3. Hand-tighten, then torque to the target value in one measured pull. 4. After pressurization, recheck torque and retighten to the same value if recommended. For safety and leak-free performance, always confirm exact torque for the specific thread size and surface finish from the adapter manufacturerâs datasheet or technical support before installation.

What maintenance checks are recommended for Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 to ensure reliable 60Â° cone sealing?

Recommended maintenance checks for Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 to ensure reliable 60Â° cone sealing: - Visual inspection: check swivel nut, cone face and thread area for nicks, gouges, corrosion or plating loss that could impair sealing. - Surface cleanliness: remove dirt, debris, paint or hydraulic fluid residues from cone and mating surfaces before assembly. - Thread condition: verify threads are undamaged and engage smoothly; replace if distorted or cross-threaded. - Cone integrity: inspect 60Â° cone for burrs, cracks or wear; small scratches may be polished out, deeper damage requires replacement. - Swivel nut operation: ensure free rotation without excessive play; lubricate threads with compatible grease to prevent galling. - Torque and assembly: tighten to specified torque and check for proper engagement depth; avoid over-tightening. - Leak test: perform pressure/functional test after assembly at working pressure and check for seepage at cone. - Regular intervals: inspect after initial service hours, then periodically based on operating conditions (e.g., monthly in harsh service).

How does thread compatibility affect sealing when using Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 with different hose fittings?

Thread compatibility is critical for reliable sealing when using Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 with various hose fittings. Key points: - Thread type and pitch match: The internal metric threads of Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 must match the male thread form and pitch of the hose fitting. Mismatched pitch or thread profile prevents proper engagement, leaving gaps that cause leaks and reduce mechanical strength. - Size and tolerance fit: Even with correct designation (e.g., M20x1.5), deviations in tolerance class between adapter and fitting can lead to loose or overly tight joints. Loose fit risks vibration-induced loosening and leakage; excessive interference can damage threads or prevent full seating of the 60Â° cone sealing surface. - Sealing method interaction: Type A705 uses swivel nuts with a 60Â° cone sealing. Proper thread compatibility ensures the swivel nut can draw the male fitting into firm contact with the cone. If threads are incompatible, the cone cannot compress uniformly, producing uneven contact and sealing failure even if threads appear engaged. - Material and galvanization: Carbon steel, galvanized components can gall or seize if threads bind. Properly matched threads plus lubrication/assembly torque avoid thread damage that would compromise the cone seal. - Thread direction and shoulder/length: Different hose fittings may have different thread engagement lengths or shoulders. If the male fitting bottoms out before the cone seats, or if thereâs insufficient engagement length, the 60Â° cone cannot seal properly. - Torque and assembly: Compatible threads allow correct torque transfer so the swivel nut compresses the cone to specification. Incompatible threads may strip or prevent required torque, leading to under- or over-tightening and leaks. - Combined systems and adapters: Using intermediate adapters or mixed standards increases riskâensure all mating parts are metric, correct class, and intended for cone sealing use. Practical guidance: verify exact metric thread designation, tolerance class, and engagement length of the hose fitting; confirm itâs designed for 60Â° cone sealing; use correct torque and assembly practices; inspect threads and galvanization for damage; use compatible seals or backup seals if specified. These measures preserve reliable sealing of Adaptor - hydraulic adapter, female thread METRIC, carbon steel, type A705 with different hose fittings.

Adapter – Fitting hydraulic, metric female thread, carbon steel, type A705

All products, High-pressure adapters/

Additional information

Material	CS – steel (cast iron)

High-pressure adapter type A705 with metric female thread, with swivel nuts (60° cone sealing). Used in power hydraulic systems to connect flexible hydraulic hoses and pipes to other components of the installation (pumps, valves, quick couplings, etc.). Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-A705-10-10	Adapter M10x1 female / M10x1 female	-	400	In stock	Enquiry
TI-A705-14-14	Adapter M14x1.5 female / M14x1.5 female	-	400	In stock	Enquiry
TI-A705-16-16	Adapter M16x1.5 female / M16x1.5 female	-	400	In stock	Enquiry
TI-A705-18-18	Adapter M18x1.5 female / M18x1.5 female	-	400	In stock	Enquiry
TI-A705-20-20	Adapter M20x1.5 female / M20x1.5 female	-	350	In stock	Enquiry
TI-A705-22-22	Adapter M22x1.5 female / M22x1.5 female	-	350	In stock	Enquiry
TI-A705-26-26	Adapter M26x1.5 female / M26x1.5 female	-	315	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

High-pressure adapter type A705 with metric female thread, with swivel nuts (60° cone sealing). Used in power hydraulic systems to connect flexible hydraulic hoses and pipes to other components of the installation (pumps, valves, quick couplings, etc.). Material: carbon steel, galvanized.