Is the Adaptor - JIS Komatsu cap GW METRIC, carbon steel, type A507 compatible with Komatsu hydraulic systems using internal metric thread and 60Â° inverted cone sealing?

Yes. Adaptor - JIS Komatsu cap GW METRIC, carbon steel, type A507 is compatible with Komatsu hydraulic systems that use internal metric threads and 60Â° inverted cone sealing. The product description.Adaptor - high-pressure blind plug JIS type A507 with internal metric thread (sealing inverted cone 60Â°) - KOMATSU.explicitly states it is designed for JIS (Komatsu) interfaces, has matching internal metric threads, and uses the 60Â° inverted cone sealing geometry. Made of carbon steel and galvanized, it is suitable for high-pressure hydraulic applications where that thread form and sealing angle are required. Ensure thread size and pressure rating match your specific system before installation.

Does the Adaptor - JIS Komatsu cap GW METRIC, carbon steel, type A507 require special installation tools for the 60Â° inverted cone seal?

Adaptor - JIS Komatsu cap GW METRIC, carbon steel, type A507 does not typically require special installation tools for the 60Â° inverted cone seal. Installation is normally performed using standard tightening tools appropriate for the capâs size and thread (torque wrench or suitable spanner) to ensure correct seating of the inverted cone. Care should be taken to clean mating surfaces and apply specified torque to avoid leaks; if manufacturer instructions specify a torque value or special tool, follow those. In absence of such a specification, standard workshop tools and a calibrated torque wrench are sufficient.

What maintenance is recommended for the Adaptor - JIS Komatsu cap GW METRIC, carbon steel, type A507 to prevent corrosion?

For the Adaptor - JIS Komatsu cap GW METRIC, carbon steel, type A507, galvanized, perform the following maintenance to prevent corrosion: 1. Regular inspection - Visually inspect before installation and at regular intervals (monthly or according to service conditions) for scratches, dents, flaking or discoloration of the galvanised coating and any signs of rust at threads, sealing faces and under deposits. 2. Cleaning - Remove dirt, grease, salt deposits and chemical residues after exposure, using mild detergent and water, then dry thoroughly. For stubborn deposits use a soft brush; avoid abrasive tools that damage the zinc coating. 3. Touch-up damaged zinc - Immediately repair any scratched or exposed base metal with a zinc-rich touch-up paint or cold galvanizing compound compatible with carbon steel galvanizing to restore sacrificial protection. 4. Thread care and sealing faces - Keep internal metric threads clean and lightly lubricated with a corrosion-inhibiting thread lubricant or anti-seize compound suitable for galvanized steel and the service media. Ensure the inverted cone 60Â° sealing face is free of nicks; protect it during handling and storage with caps or soft covers. 5. Environmental control - Minimize long-term exposure to corrosive atmospheres (salt spray, acidic/alkaline conditions). If used in aggressive environments, increase inspection frequency and consider additional protective coatings or sacrificial anodes where feasible. 6. Avoid incompatible chemicals - Do not expose the adaptor to strong acids, alkalis or chlorinated solvents that can attack zinc. Rinse promptly if accidental exposure occurs. 7. Proper storage - Store in a dry, ventilated area off the ground, separated from corrosive materials. Use desiccants or controlled humidity for extended storage. 8. Correct installation and handling - Use recommended torque values and proper tools to avoid damaging the galvanised surface. Avoid impact or bending that can fracture the coating. 9. Replacement criteria - Replace the Adaptor - JIS Komatsu cap GW METRIC, carbon steel, type A507 if deep corrosion reaches base metal, threads are significantly damaged, or the sealing surface integrity is compromised. Following these steps will help maintain the galvanised protection and extend service life while preventing corrosion-related failures.

Adapter – cap JIS Komatsu with metric female, carbon steel, type A507

All products, High-pressure adapters/

Additional information

Material	CS – steel (cast iron)

Adapter – cap high-pressure JIS type A507 with metric female thread (inverted 60° cone sealing) – KOMATSU. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-A507-14	Cap M14x1.5 female JIS	-	345	In stock	Enquiry
TI-A507-16	Cap M16x1.5 female JIS	-	345	In stock	Enquiry
TI-A507-18	Cap M18x1.5 female JIS	-	345	In stock	Enquiry
TI-A507-22	Cap M22x1.5 female JIS	-	345	In stock	Enquiry
TI-A507-24	Cap M24x1.5 female JIS	-	275	In stock	Enquiry
TI-A507-30	Cap M30x1.5 female JIS	-	205	In stock	Enquiry
TI-A507-33	Cap M33x1.5 female JIS	-	205	In stock	Enquiry