Is the DRY-MATE dry-cutting connector plug with GW, polypropylene suitable for flammable liquids or gases?

No. The DRY-MATE dry-cutting connector plug with GW, polypropylene is not suitable for flammable liquids or gases. The product description explicitly states it is not intended for gas media and liquids with a low flash point. It is designed for chemical, pharmaceutical, agricultural and handling systems, installed on the pressure (tank) side, with materials (glass-fiber reinforced polypropylene body, PTFE ball and sealing, AISI 316 latches) and operating limits (up to 7 bar, 21Â°C standard; up to 66Â°C at 5 bar) that do not qualify it for use with flammable media.

Can the DRY-MATE dry-cutting connector plug with GW, polypropylene be used on the suction (pump) side instead of the pressure (tank) side?

No - the DRY-MATE dry-cutting connector plug with GW, polypropylene is specified for installation on the pressure (tank) side. Its design (ball-valve type, materials, sealing and rated working pressure/temperature) and manufacturer instructions indicate it is not intended for use on the suction (pump) side. Using it on the pump side could impair performance and safety.

Does the DRY-MATE dry-cutting connector plug with GW, polypropylene require specific maintenance or inspection intervals?

DRY-MATE dry-cutting connector plug with GW, polypropylene does not require complex maintenance but should be inspected and maintained periodically to ensure reliable operation and sealing. Recommended maintenance and inspection intervals: - Visual inspection: before each use. check for cracks, damage to the body, caps, CAMLOCK latches (AISI 316) and visible wear on the ball/seat area. - Functional check: weekly or before any critical transfer. operate the valve to confirm unobstructed flow and smooth ball movement. - Seal inspection: monthly. inspect PTFE valve sealing surfaces for wear, deformation or contamination; replace if sealing performance is compromised or leakage approaches the maximum specified (2 ml). - Deeper inspection/servicing: every 6â12 months depending on frequency of use, media aggressiveness and operating conditions (pressure up to 7 bar, temperature up to 66Â°C at reduced pressure). For aggressive chemicals or heavy use, shorten interval. - After abnormal events: immediately inspect after overpressure, impact, exposure to incompatible fluids (note: not suitable for gas media or low flash point liquids) or exposure above rated temperature/pressure. Maintenance tips: - Clean with compatible, nonâaggressive agents; avoid solvents that attack polypropylene or PTFE. - Ensure CAMLOCK latches (AISI 316) are corrosionâfree and function properly; lubricate with a compatible lubricant if needed. - Replace caps when worn to protect the thread and keep contaminants out. - Keep records of inspections and any replacements. These intervals are general recommendations; adjust based on actual operating conditions and company safety procedures.

Plug coupling dry-break DRY-MATE with female thread, polypropylene

All products, Loading and unloading couplings/

Additional information

Material	P – material (plastic)

Plug coupling dry-break DRY-MATE with a thread internal with polypropylene. Used in the chemical, pharmaceutical industry, agriculture and transfer systems. Nie is intended for media gas and liquids o low the point ignition. Installed on the pressure side (tank side). The plug design is based on a ball valve, which ensures a completely unobstructed flow. The plug is supplied complete with polypropylene caps. Material: body – polypropylene glass-fiber-reinforced, ball – PTFE, latch CAMLOCK – steel AISI 316. Sealing: valve – PTFE. pressure working: up to 7 bar. Operating temperature: 21°C (up to 66°C at pressure working 5 bar). Maximum leakage: 2 ml.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AC-DMA150-PP-BSP	Plug DRY MATE DN38 with 1.1/2" BSP female, polypropylene	-	7	In stock	Enquiry
AC-DMA150-PP-NPT	Plug DRY MATE DN38 with 1.1/2" NPT female, polypropylene	-	7	In stock	Enquiry
AC-DMA200-PP-BSP	Plug DRY MATE DN38 with 2" BSP female, polypropylene	-	7	In stock	Enquiry
AC-DMA200-PP-NPT	Plug DRY MATE DN38 with 2" NPT female, polypropylene	-	7	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Plug coupling dry-break DRY-MATE with a thread internal with polypropylene. Used in the chemical, pharmaceutical industry, agriculture and transfer systems. Nie is intended for media gas and liquids o low the point ignition. Installed on the pressure side (tank side). The plug design is based on a ball valve, which ensures a completely unobstructed flow. The plug is supplied complete with polypropylene caps. Material: body – polypropylene glass-fiber-reinforced, ball – PTFE, latch CAMLOCK – steel AISI 316. Sealing: valve – PTFE. pressure working: up to 7 bar. Operating temperature: 21°C (up to 66°C at pressure working 5 bar). Maximum leakage: 2 ml.