Can the MSL rail coupling with GW 5.1/2" DIN11, with hose end, aluminum withstand continuous operation at 16 bar and -20Â°C to +65Â°C?

Yes . based on the provided specification, the MSL rail coupling with GW 5.1/2" DIN11, with hose end, aluminum is rated for a working pressure of 16 bar and an operating temperature range of â20Â°C to +65Â°C. Assuming the actual assembly uses the specified aluminum end piece, appropriate hose mounting method (shell clamp or crimping sleeve), and compatible seals/materials rated for that temperature range and pressure, the coupling is designed to withstand continuous operation at 16 bar within â20Â°C to +65Â°C. Caveats: ensure the hose, clamp/crimp, and seals are certified for 16 bar and the full temperature span; verify corrosion, vibration and dynamic load conditions in the rail environment; perform pressure testing and periodic inspections per applicable standards before and during service.

Is the MSL rail coupling with GW 5.1/2" DIN11, with hose end, aluminum compatible with different sealing materials for -20Â°C to +65Â°C operation?

MSL rail coupling with GW 5.1/2" DIN11, with hose end, aluminum can be compatible with different sealing materials for operation from -20Â°C to +65Â°C, but compatibility depends on the chosen seal. The product specification lists operating temperature â20Â°C to +65Â°C âor a wider range depending on material, sealing, and applicationâ, so you must select seals rated for that range (e.g., nitrile/NBR typically OK to ~â30Â°Câ¦+100Â°C, EPDM good for â40Â°Câ¦+120Â°C, FKM/Viton for â20Â°Câ¦+200Â°C). Also verify chemical compatibility with the media, swelling/ageing, and maintain pressure rating (16 bar). For final selection and safety, consult seal manufacturer datasheets and perform application-specific validation.

Does the MSL rail coupling with GW 5.1/2" DIN11, with hose end, aluminum support higher pressures for short-duration spikes?

MSL rail coupling with GW 5.1/2" DIN11, with hose end, aluminum Format is specified with a nominal working pressure of 16 bar and operating temperature range â20 Â°C to +65 Â°C (subject to sealing and application). That rating means the coupling and its aluminum hose end are designed for sustained operation up to 16 bar. Short-duration pressure spikes above the rated 16 bar are not guaranteed safe: aluminum end pieces, hose assemblies, seals and any crimp/shell clamp are the limiting elements and may fail if subjected to transient overpressure. If you expect short-duration spikes, you should: - Consult the manufacturerâs explicit overpressure or burst safety margins and dynamic pressure recommendations for this exact format. - Verify the hose, sealing material and crimp/shell clamp rating; the coupling alone does not ensure the whole assembly tolerates spikes. - Consider pressure relief devices, dampeners or specifying components with higher working pressure or defined surge capacity. Conclusion: MSL rail coupling with GW 5.1/2" DIN11, with hose end, aluminum Format is rated 16 bar; it should not be assumed to safely withstand higher short-duration spikes without manufacturer confirmation and checks of the complete hose assembly.

MSL rail coupling with GW 5.1/2″ DIN11, with hose end, aluminum

All products, Loading and unloading couplings/

Additional information

Material	AL – aluminum

Railway loading connector with internal thread 5.1/2″ DIN 11 – nut, with a smooth “tail” for hose mounting to a shell clamp (or crimping sleeve). Material: aluminum (applies to the end piece). Working pressure: 16 bar. Operating temperature: from -20°C to +65°C (or a wider range depending on material, sealing, and application).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
GD-MSL-DIN-075-AL	MSL connector GW 5.1/2" DIN11, for hose 75 mm, aluminum	75	16	In stock	Enquiry
GD-MSL-DIN-075-AL1	MSL connector GW 5.1/2" DIN11, for hose 75 mm, aluminum	75	16	In stock	Enquiry
GD-MSL-DIN-100-AL	MSL connector GW 5.1/2" DIN11, for hose 100 mm, aluminum	100	16	In stock	Enquiry
GD-MSL-DIN-100-AL1	MSL connector GW 5.1/2" DIN11, for hose 100 mm, aluminum	100	16	In stock	Enquiry
GD-MSL-DIN-100-ALMS	MSL GW 5.1/2" DIN11 connector, for hose 100 mm, aluminum, brass nut	100	16	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Railway loading connector with internal thread 5.1/2″ DIN 11 – nut, with a smooth “tail” for hose mounting to a shell clamp (or crimping sleeve). Material: aluminum (applies to the end piece). Working pressure: 16 bar. Operating temperature: from -20°C to +65°C (or a wider range depending on material, sealing, and application).