Is the Extraction hose for exhaust fumes, gases NEOPRENE 1 suitable for continuous use at +150Â°C?

Extraction hose for exhaust fumes, gases NEOPRENE 1 is rated for continuous operation from -35Â°C to +135Â°C. It may be exposed temporarily to temperatures up to +150Â°C, but +150Â°C is not specified as a continuous operating temperature. Therefore it is not suitable for continuous use at +150Â°C; use at that temperature should be limited to short-term/temporary exposure only.

Can Extraction hose for exhaust fumes, gases NEOPRENE 1 be used for short-term exposure to chemicals or solvents?

Extraction hose for exhaust fumes, gases NEOPRENE 1 is chemically resistant and used for extracting hot vapors, gases and exhausts, but it is not specifically certified for prolonged chemical or solvent exposure. For short-term exposure to many chemicals or solvents it can be suitable thanks to its neoprene (chloroprene) lining and glass-fiber reinforcement; however, compatibility depends on the specific chemical, concentration and temperature. For safety, check the chemical compatibility of neoprene with the particular solvent and avoid temperatures above the hoseâs limits (-35Â°C to +135Â°C, temporary up to +150Â°C). For aggressive solvents or where contamination/degradation risk is critical, use a hose with specific chemical-resistance certification.

Can Extraction hose for exhaust fumes, gases NEOPRENE 1 be used for vehicle engine cooling air?

Yes. Extraction hose for exhaust fumes, gases NEOPRENE 1 can be used for vehicle engine cooling air. The product description explicitly lists use âin vehicles and engines for cooling airâ and for the extraction/discharge of hot vapors, gases and cooling air. Key suitability points from the spec: - Temperature range: continuous -35Â°C to +135Â°C (short-term up to +150Â°C). appropriate for typical engine cooling-air temperatures. - Construction: glass fabric impregnated with black CR (neoprene), steel wire internal spiral and external fiberglass strand. gives flexibility, crush resistance and shape retention under airflow and vibration. - Smooth internal surface when straightened and very small bending radius. useful for routing in tight engine bays. - Chemical, UV and aging resistance. helps withstand under-hood environment. - Mounting: designed to be clamped, compatible with common vehicle hose fixtures. Considerations before final fitment: - Verify peak local temperatures in your specific engine bay do not exceed the short-term +150Â°C limit. - Ensure diameter, length and end fittings match your cooling-air system and that clamps provide a secure seal. - For prolonged exposure to engine oils, fuel vapors or specific aggressive chemicals, confirm chemical compatibility with neoprene or consider an alternative material rated for those substances.

Extraction hose for exhaust fumes, gases NEOPRENE 1

All products, Ducting and ventilation hoses/

Additional information

Material	GF – fiberglass
Maximum operating temperature [°C]	135
Minimum operating temperature [°C]	-35
Vacuum resistance	yes
Standard length [m]	10, 4, 61
Reinforcement	steel spiral

Lightweight, single-layer, highly flexible and elastic hose designed for the extraction of hot vapors, smoke, gases, blowing, and the discharge of cooling air. Chemically resistant, UV resistant, and aging resistant. Used, among others, for hot air in granulate dryers and film blowers in plastic processing, in paint dryers in printing houses, other industrial dryers, in the electronics industry, in vehicles and engines for cooling air, incinerators, as well as for the extraction of exhaust gases and welding gases. Smooth inside (when straightened), with a very small bending radius allowing easy installation in tight spaces of equipment and vehicles. Mounted with clamps. Other diameters and lengths, soft ends of sections, etc., available on special order. Hose material: glass fabric impregnated with black CR rubber (Neoprene® – chloroprene rubber). Reinforcement: internal spiral of steel wire, external strand of fiberglass. Operating temperature: from -35°C to +135°C (temporarily up to +150°C).

List of product variants

Article number	Product variant name	Nominal inner diameter	Working pressure [bar]
TS-NEOPRENE1-013	NEOPRENE Hose 1 13 mm	12	1.5
TS-NEOPRENE1-016	NEOPRENE hose 1 16 mm	16	1.5
TS-NEOPRENE1-018	NEOPRENE Hose 1 18 mm	18	1.5
TS-NEOPRENE1-019	Neoprene Hose 1 19 mm	20	1.5
TS-NEOPRENE1-022	NEOPRENE hose 1 22 mm	22	1.5
TS-NEOPRENE1-025	NEOPRENE hose 1 25 mm	25	1.4
TS-NEOPRENE1-032	NEOPRENE hose 1 32 mm	32	1.4
TS-NEOPRENE1-034	NEOPRENE hose 1 34 mm	35	1.4
TS-NEOPRENE1-035	NEOPRENE hose 1 35 mm	35	1.4
TS-NEOPRENE1-036	NEOPRENE Hose 1 36 mm	35	1.4
TS-NEOPRENE1-038	NEOPRENE hose 1 38 mm	38	1.4
TS-NEOPRENE1-039	NEOPRENE Hose 1 39 mm	38	1.4
TS-NEOPRENE1-041	NEOPRENE hose 1 41 mm	40	1.3
TS-NEOPRENE1-044	NEOPRENE hose 1 44 mm	45	1.2
TS-NEOPRENE1-051	NEOPRENE Hose 1 51 mm	50	1.2
TS-NEOPRENE1-055	NEOPRENE hose 1 55 mm	55	1.1
TS-NEOPRENE1-057	NEOPRENE hose 1 57 mm	55	1.1
TS-NEOPRENE1-060	NEOPRENE hose 1 60 mm	60	1.1
TS-NEOPRENE1-063	NEOPRENE hose 1 63 mm	65	1.1
TS-NEOPRENE1-065	Neoprene Hose 1 65 mm	65	1.1
TS-NEOPRENE1-070	NEOPRENE hose 1 70 mm	70	1.1
TS-NEOPRENE1-076	NEOPRENE hose 1 76 mm	75	1
TS-NEOPRENE1-080	Neoprene hose 1 80 mm	80	1
TS-NEOPRENE1-083	Neoprene hose 1 83 mm	80	1
TS-NEOPRENE1-090	NEOPRENE Hose 1 90 mm	90	0.9
TS-NEOPRENE1-095	Neoprene Hose 1 95 mm	90	0.9
TS-NEOPRENE1-102	Neoprene Hose 1 102 mm	100	0.9
TS-NEOPRENE1-108	NEOPRENE hose 1 108 mm	100	0.8
TS-NEOPRENE1-110	Neoprene Hose 1 110 mm	110	0.8
TS-NEOPRENE1-114	Neoprene Hose 1 114 mm	110	0.8
TS-NEOPRENE1-120	NEOPRENE hose 1 120 mm	120	0.8
TS-NEOPRENE1-127	Neoprene Hose 1 127 mm	125	0.8
TS-NEOPRENE1-130	NEOPRENE hose 1 130 mm	130	0.8
TS-NEOPRENE1-140	NEOPRENE hose 1 140 mm	140	0.8
TS-NEOPRENE1-152	Neoprene Hose 1 152 mm	150	0.6
TS-NEOPRENE1-160	NEOPRENE hose 1 160 mm	160	0.6
TS-NEOPRENE1-165	NEOPRENE hose 1 165 mm	160	0.6
TS-NEOPRENE1-178	NEOPRENE hose 1 178 mm	180	0.6
TS-NEOPRENE1-180	NEOPRENE Hose 1 180 mm	180	0.6
TS-NEOPRENE1-203	NEOPRENE hose 1 203 mm	200	0.5
TS-NEOPRENE1-220	NEOPRENE hose 1 220 mm	220	0.4
TS-NEOPRENE1-230	NEOPRENE Hose 1 230 mm	225	0.4
TS-NEOPRENE1-254	NEOPRENE hose 1 254 mm	250	0.4
TS-NEOPRENE1-305	NEOPRENE hose 1 305 mm	300	0.1

Lightweight, single-layer, highly flexible and elastic hose designed for the extraction of hot vapors, smoke, gases, blowing, and the discharge of cooling air. Chemically resistant, UV resistant, and aging resistant. Used, among others, for hot air in granulate dryers and film blowers in plastic processing, in paint dryers in printing houses, other industrial dryers, in the electronics industry, in vehicles and engines for cooling air, incinerators, as well as for the extraction of exhaust gases and welding gases. Smooth inside (when straightened), with a very small bending radius allowing easy installation in tight spaces of equipment and vehicles. Mounted with clamps. Other diameters and lengths, soft ends of sections, etc., available on special order. Hose material: glass fabric impregnated with black CR rubber (Neoprene® – chloroprene rubber). Reinforcement: internal spiral of steel wire, external strand of fiberglass. Operating temperature: from -35°C to +135°C (temporarily up to +150°C).

Additional information

Material	GF – fiberglass
Maximum operating temperature [°C]	135
Minimum operating temperature [°C]	-35
Vacuum resistance	yes
Standard length [m]	10, 4, 61
Reinforcement	steel spiral