Can Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel withstand continuous operation at 160Â°C and 250 bar pressure?

Yes . Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel Format is rated for continuous operation at up to +160Â°C and a working pressure of up to 250 bar. Based on the provided specifications (operating temperature up to +160Â°C; working pressure up to 250 bar; maximum pressure 280 bar; material: galvanized steel), it can withstand continuous use at 160Â°C and 250 bar within those limits. Caveats to consider: - Continuous exposure at the limits (160Â°C and 250 bar) may accelerate wear, corrosion, or fatigue compared with milder conditions. Galvanized steel has corrosion resistance but is not as durable at high temperatures as stainless steel. - Ensure connections, seals, and the rest of your system (hoses, Oârings, fittings) are rated for 160Â°C and 250 bar . the lance alone meeting specs does not guarantee system-wide compatibility. - Follow manufacturer installation, maintenance, and inspection intervals; avoid pressure or thermal spikes above the stated maximum pressure (280 bar) or temperature above 160Â°C. If you need long-term reliability under continuous high-temperature conditions, consider materials specifically rated for prolonged 160Â°C operation (e.g., stainless steel) or consult the manufacturer for recommended duty cycles.

Is Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel safe for short bursts at 280 bar and 160Â°C?

Based on the provided specs, Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel has a maximum pressure rating of 280 bar and an operating temperature rating up to +160Â°C. Running short bursts exactly at 280 bar and 160Â°C would be at the stated maxima and therefore is at the limit of the componentâs rated capability. That means it may be acceptable for occasional short bursts but carries higher risk (no safety margin), increased wear and potential for failure if conditions fluctuate, connections are stressed, or the lance has damage/corrosion. For safe longâterm or routine use, operate below the maximums and follow manufacturer inspection, maintenance and safety guidelines. If in doubt, consult the manufacturer for confirmation and recommended safety margins.

Can Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel be used with chemical detergents at 160Â°C and 250 bar?

Yes. Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel can be used with chemical detergents at 160Â°C and 250 bar only if those detergents are chemically compatible with galvanized steel and suitable for use at that temperature and pressure. Key points to verify before use: - Temperature and pressure: the lance ratings (operating temperature up to +160Â°C and working pressure up to 250 bar) match your stated conditions. - Chemical compatibility: galvanizing (zinc coating) can be attacked by strong acids, strong alkalis, some solvents and ammonium compounds, causing corrosion, coating damage or zinc leaching. Check the detergentâs safety/technical data sheet for compatibility with zinc/galvanized steel. - Seal and hose materials: ensure fittings, O-rings and any seals in the gun/hose assembly are rated for 160Â°C and compatible with the detergent; these components often limit chemical/temperature resistance. - Concentration and exposure: high concentrations, long contact times or elevated temperatures increase corrosion risk. - Safety and warranty: follow manufacturer recommendations; using incompatible chemicals may void warranty or create safety hazards. If chemical compatibility is confirmed for galvanized steel and all connected components are rated for 160Â°C and 250 bar, the Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel is suitable. Otherwise choose a lance made of chemically resistant material (e.g., stainless steel) or adjust detergent formulation/conditions.

Extension lance 325 mm, for high-pressure cleaner gun, galvanized steel

All products, Guns for high-pressure washers/

Additional information

Thermal insulated extension lance, designed for high-pressure washer. Length: 325 mm. Connections: (inlet) GZ 1/4″ BSP / (outlet) GZ 1/4″ BSP. Working pressure: up to 250 bar. Maximum pressure: 280 bar. Flow rate: 45 l/min. Operating temperature: up to +160°C. Material: galvanized steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
MH-1020310111	Isolated extension chain 325 mm, galvanized carbon steel.	-	250	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Thermal insulated extension lance, designed for high-pressure washer. Length: 325 mm. Connections: (inlet) GZ 1/4″ BSP / (outlet) GZ 1/4″ BSP. Working pressure: up to 250 bar. Maximum pressure: 280 bar. Flow rate: 45 l/min. Operating temperature: up to +160°C. Material: galvanized steel.