Can AGJ hydraulic end, type ZJZ110 (carbon steel, galvanized) be crimped using standard crimping sleeves for hydraulic hoses and which sleeve size is recommended?

Yes . the AGJ hydraulic end, type ZJZ110, carbon steel (galvanized) can be crimped using standard crimping sleeves intended for hydraulic and industrial hoses. The product description explicitly states it is "designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose," which means you must match the sleeve to the hose construction (e.g., single wire, spiral, textile) and the hose inner diameter. Recommended sleeve size: choose the sleeve whose internal diameter corresponds to the hose nominal inside diameter plus the wall thickness, per the hose manufacturerâs crimping chart. In practice: - For common EN/ISO hydraulic hoses (e.g., 1SN/2SN, R1/R2), use the sleeve size recommended by the hose maker for the hose nominal size (e.g., 1/4", 3/8", 1/2", 3/4", 1"). - If you only have hose nominal size, use the standard sleeve size for that nominal (e.g., 1/2" hose â 1/2" sleeve as specified by hose/sleeve charts). Important: verify compatibility with the hose manufacturerâs crimping dimension sheet and the crimping machine settings (jaw profile and crimp diameter). If uncertain, provide the exact hose type and nominal size to get the precise sleeve part number and crimp dimensions.

Can AGJ hydraulic end, type ZJZ110, carbon steel be crimped on industrial hoses using standard crimping sleeves and which sleeve size fits best?

Yes. The AGJ hydraulic end, type ZJZ110, carbon steel (standard Z with external UNF thread and 74Â° cone sealing) is designed for crimping on hydraulic and industrial hoses. Use a crimping sleeve matched to the hose construction and diameter specified by the hose manufacturer; standard crimp sleeves for industrial/hydraulic hoses of the same nominal hose size are appropriate. For best fit, select the sleeve sized to the hose nominal ID/OD per the hose makerâs crimp specification-typically the sleeve size corresponding to the hose nominal series (e.g., for a 1/2" hose use the 1/2" sleeve). Always verify sleeve dimensions and crimp specs against the hose manufacturer and perform pressure testing after crimping.

Can AGJ hydraulic end, type ZJZ110, carbon steel be used with hoses requiring a 74Â° cone seal and which thread adapters fit?

Yes. AGJ hydraulic end, type ZJZ110, carbon steel can be used with hoses that require a 74Â° cone seal. The product description states it is a Standard hydraulic end (type Z) with an external UNF thread and seals on a 74Â° cone (AGJ), specifically designed for crimping into hydraulic and industrial hoses using a matching crimping sleeve. Its carbon steel, galvanized construction is suitable for typical hydraulic service. Which thread adapters fit: - Any adapter or counterpart with the matching UNF external thread size and internal female UNF thread designed to mate with a 74Â° cone (JIC/AGJ-style) seal can be used. - Confirm the exact UNF thread nominal size and pitch of the ZJZ110 (e.g., 7/16-20 UNF, 9/16-18 UNF, 3/4-16 UNF, etc.) from the manufacturerâs dimension table. Use an adapter or port with the identical UNF thread specification and a 74Â° cone seat. - Use standard JIC/74Â° cone adapters, couplings, or fittings specified for the identified UNF size. If adapting to a different thread type (BSPP, BSPT, metric), use a suitable thread adapter that provides a female UNF port with a 74Â° cone seat. Important checks before assembly: - Verify the exact UNF thread size/pitch of ZJZ110 from technical data. - Ensure the mating fitting has a proper 74Â° cone seat and is rated for required pressure. - Use the correct crimping sleeve for the hose type and follow crimp specs. - Inspect galvanizing and compatibility with hydraulic fluid and environment. In short: compatible with hoses needing a 74Â° cone seal when paired with fittings/adapters matching the ZJZ110âs UNF thread size and a 74Â° cone seat (standard JIC/AGJ adapters).

AGJ hydraulic end, type ZJZ110, carbon steel

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)
Standard length [m]	50

Standard hydraulic end (type Z – with a regular hydraulic “tail” for the hose), with external UNF thread, sealing on a 74° cone (AGJ). Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZJZ110-07-03	End. JIC GZ 7/16", hose 3/16", cone 74°	5	-	In stock	Enquiry
TI-ZJZ110-07-04	End. JIC GZ 7/16", hose 1/4", cone 74°	6	-	In stock	Enquiry
TI-ZJZ110-08-04	End. JIC GZ 1/2", hose 1/4", cone 74°	6	-	In stock	Enquiry
TI-ZJZ110-08-05	End. JIC GZ 1/2", hose 5/16", cone 74°	8	-	In stock	Enquiry
TI-ZJZ110-09-04	End. JIC GZ 9/16", hose 1/4", cone 74°	6	-	In stock	Enquiry
TI-ZJZ110-09-05	End. JIC GZ 9/16", hose 5/16", cone 74°	8	-	In stock	Enquiry
TI-ZJZ110-09-06	End. JIC GZ 9/16", hose 3/8", cone 74°	10	-	In stock	Enquiry
TI-ZJZ110-10-05	End. JIC GZ 5/8", hose 5/16", cone 74°	8	-	In stock	Enquiry
TI-ZJZ110-10-06	End. JIC GZ 5/8", hose 3/8", cone 74°	10	-	In stock	Enquiry
TI-ZJZ110-12-04	End. JIC GZ 3/4", hose 1/4", cone 74°	6	-	In stock	Enquiry
TI-ZJZ110-12-05	End. JIC GZ 3/4", hose 5/16", cone 74°	8	-	In stock	Enquiry
TI-ZJZ110-12-06	End. JIC GZ 3/4", hose 3/8", cone 74°	10	-	In stock	Enquiry
TI-ZJZ110-12-08	End. JIC GZ 3/4", hose 1/2", cone 74°	12	-	In stock	Enquiry
TI-ZJZ110-12-10	End. JIC GZ 3/4", hose 5/8", cone 74°	16	-	In stock	Enquiry
TI-ZJZ110-14-06	End. JIC GZ 7/8", hose 3/8", cone 74°	10	-	In stock	Enquiry
TI-ZJZ110-14-08	End. JIC GZ 7/8", hose 1/2", cone 74°	12	-	In stock	Enquiry
TI-ZJZ110-14-10	End. JIC GZ 7/8", hose 5/8", cone 74°	16	-	In stock	Enquiry
TI-ZJZ110-17-08	End. JIC GZ 1.1/16", hose 1/2", cone 74°	12	-	In stock	Enquiry
TI-ZJZ110-17-10	End. JIC GZ 1.1/16", hose 5/8", cone 74°	16	-	In stock	Enquiry
TI-ZJZ110-17-12	End. JIC GZ 1.1/16", hose 3/4", cone 74°	20	-	In stock	Enquiry
TI-ZJZ110-19-12	End. JIC GZ 1.3/16", hose 3/4", cone 74°	20	-	In stock	Enquiry
TI-ZJZ110-19-16	End. JIC GZ 1.3/16", hose 1", cone 74°	25	-	In stock	Enquiry
TI-ZJZ110-21-12	End. JIC GZ 1.5/16", hose 3/4", cone 74°	20	-	In stock	Enquiry
TI-ZJZ110-21-16	End. JIC GZ 1.5/16", hose 1", cone 74°	25	-	In stock	Enquiry
TI-ZJZ110-26-16	End. JIC GZ 1.5/8", hose 1", cone 74°	25	-	In stock	Enquiry
TI-ZJZ110-26-20	End. JIC GZ 1.5/8", hose 1.1/4", cone 74°	32	-	In stock	Enquiry
TI-ZJZ110-30-20	End. JIC GZ 1.7/8", hose 1.1/4", cone 74°	32	-	In stock	Enquiry
TI-ZJZ110-30-24	End. JIC GZ 1.7/8", hose 1.1/2", cone 74°	38	-	In stock	Enquiry
TI-ZJZ110-40-32	End. JIC GZ 2.1/2", hose 2", cone 74°	50	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Standard hydraulic end (type Z – with a regular hydraulic “tail” for the hose), with external UNF thread, sealing on a 74° cone (AGJ). Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: carbon steel, galvanized.