Can INTERLOCK straight end GZ BSP, carbon steel, be used with 4SH, R13, and R15 hoses and what BSP sizes and pressure ratings are compatible?

Yes. INTERLOCK straight end GZ BSP, carbon steel, can be used with 4SH, R13, and R15 hoses . the description specifically states it is for hose type 4SH, R13, and R15. Being a straight INTERLOCK end with external BSP thread and 60Â° cone, it mates with BSP male/female ports designed for a 60Â° cone sealing surface. Compatible BSP sizes and pressure ratings depend on the specific INTERLOCK part dimensions and the hose/assembly rating, but typical compatibility guidance: - BSP thread sizes: commonly available for hose fittings in sizes from 1/4" up to 2" BSP (check the supplierâs part list for exact options). Choose the BSP size matching the hose crimp ferrule and port thread. - Pressure ratings: limited by the lowest-rated component (hose, crimp, fitting). Typical working pressures for these hose types: - 4SH: up to ~420â580 bar depending on size - R13: comparable to 4SH, high-pressure up to ~420â540 bar - R15: lower-pressure return/medium service, generally lower than 4SH/R13 (consult spec) Always verify the exact INTERLOCK fittingâs rated working pressure and size chart from the manufacturer, and ensure the hose assembly (hose, ferrule, crimp, and fitting) is certified for the intended working and burst pressures and for the exact BSP thread size.

Can INTERLOCK straight end GZ BSP, carbon steel, be used for 4SH, R13, and R15 hoses with a 60Â° cone and external BSP threads?

Yes. INTERLOCK straight end GZ BSP, carbon steel can be used for 4SH, R13, and R15 hoses with a 60Â° cone and external BSP threads. The product description explicitly states it is a Straight INTERLOCK end with external BSP thread, 60Â° cone, for hose type 4SH, R13, and R15, made of carbon steel and galvanized, matching those hose specifications and thread/cone requirements. Ensure correct hose size and proper assembly/crimping per manufacturer's guidelines and pressure ratings before use.

Are there specific BSP thread sealing requirements for INTERLOCK straight end GZ BSP, carbon steel, with 60Â° cone?

Yes. there are specific BSP thread sealing considerations for INTERLOCK straight end GZ BSP, carbon steel with a 60Â° cone. Key points: - Thread type: GZ BSP (external parallel BSP) is a parallel (cylindrical) thread; it does not seal by the thread flank alone. - Primary seal: The 60Â° cone on the fitting provides the primary metal-to-metal seal when mated to a corresponding female cone seat. Proper face contact and torque are essential to obtain a reliable cone seal. - Thread sealing: Because the BSP thread is parallel, a secondary seal on the threads is normally required to prevent leakage and protect threads from corrosion. Typical methods: - PTFE tape (thread seal tape) applied correctly to the male threads (avoid covering the cone seating face). - Liquid thread sealant (anaerobic or PTFE-based) applied to threads. - O-rings or bonded seals are not typical for plain 60Â° cone INTERLOCK unless the mating female component is designed with an O-ring groove. - Installation: Clean threads and cone faces, apply chosen sealant only to the thread portion (not the cone seat), assemble and tighten to manufacturerâs recommended torque to compress the cone and form the metal-to-metal seal. Over-tightening can damage the cone; under-tightening can leak. - Material considerations: Carbon steel, galvanized. be mindful that some sealants and tapes can interact with plating; choose compatible products to avoid galvanic issues or contamination. Galvanized finish reduces corrosion but may affect sealing surfaces if damaged. - Hose compatibility: Design is for hose types 4SH, R13, R15. ensure mating female port and sealing method are compatible with these hose assembly pressures and application. Recommendation: Follow the INTERLOCK fitting manufacturerâs assembly and sealing instructions (torque values, specific sealant types). If manufacturer guidance is unavailable, use PTFE tape or approved thread sealant on threads, avoid contaminating the cone face, and tighten to appropriate torque to ensure the 60Â° cone provides the primary seal.

INTERLOCK straight end GZ BSP, carbon steel

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)

Straight INTERLOCK end with external BSP thread, 60° cone, for hose type 4SH, R13, and R15. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ILBZ110-12-12	End. INTERLOCK GZ 3/4" BSP, hose 3/4"	20	-	In stock	Enquiry
TI-ILBZ110-16-16	End. INTERLOCK GZ 1" BSP, hose 1"	25	-	In stock	Enquiry
TI-ILBZ110-20-20	End. INTERLOCK GZ 1.1/4" BSP, hose 1.1/4"	32	-	In stock	Enquiry
TI-ILBZ110-24-24	End. INTERLOCK GZ 1.1/2" BSP, hose 1.1/2"	38	-	In stock	Enquiry
TI-ILBZ110-32-32	End. INTERLOCK GZ 2" BSP, hose 2"	50	-	In stock	Enquiry