Is VERSILON PTFE smooth-walled Teflon hose suitable for transporting flammable liquids and gases at elevated temperatures up to +260Â°C?

VERSILON PTFE smooth-walled Teflon hose can be used for transporting many flammable liquids and gases and is rated for operating temperatures up to +260Â°C. However, important safety limitations apply: - It is designed for low-pressure installations; working pressure ranges from 2.3 to 10.8 bar depending on diameter and decreases with temperatures above 20Â°C. Check the specific hose diameter and temperature to confirm both working and burst pressures (safety factor n = 4:1). - The hose is not antistatic and does not dissipate electric charges for non-conductive substances. For flammable liquids/gases, static charge accumulation can create an ignition risk.use only with adequate grounding/earthing, or choose an antistatic/conductive alternative when static mitigation is required. - It is flame retardant (UL94 V-0) and has a high oxygen index, but flame retardancy does not eliminate risks from flammable fluids or vapors under service conditions. - Not recommended for pneumatic plug connections; suitability for specific fittings and jointing must be verified for pressure, temperature and fluid compatibility. Conclusion: VERSILON PTFE smooth-walled Teflon hose is chemically compatible and temperature-rated up to +260Â°C for many flammable liquids and gases, but only if the working pressure at the intended temperature and diameter is adequate, and suitable measures are taken to control static and ensure correct fittings. If static dissipation is required or conditions approach pressure/temperature limits, use a conductive/antistatic hose or consult the manufacturer for a certified solution.

Can VERSILON PTFE smooth-walled Teflon hose be used with conductive fluids or in applications requiring antistatic properties?

No - VERSILON PTFE smooth-walled Teflon hose is not antistatic and does not dissipate electric charges for non-conductive substances. It is therefore not suitable for handling conductive fluids where antistatic or conductive hose properties are required, or for applications that demand charge dissipation to prevent sparks or static buildup. Use a specifically designed antistatic or conductive hose for such applications.

Does VERSILON PTFE smooth-walled Teflon hose require special supports or guides due to its low friction and flexibility?

Yes. Because VERSILON PTFE smooth-walled Teflon hose is highly flexible with a very low friction coefficient and is non-conductive, it does require appropriate supports or guides in many installations to ensure safe, reliable performance. Practical points: - Support spacing: use closer supports than for stiffer hoses to prevent sagging, kinking or excessive bending that could reduce working pressure or cause mechanical damage. - Guides and clamps: choose low-friction, non-abrasive guides or lined clamps to avoid damaging the smooth PTFE wall; avoid overly tight clamping that can compress or deform the hose. - Routing: provide controlled bend radii consistent with the hose diameter to maintain flow and pressure ratings; remember burst and working pressures drop at temperatures above 20Â°C. - Electrical considerations: since the hose is not antistatic for non-conductive media, use conductive supports/earthing or separate antistatic measures where charge dissipation or ignition risk exists. - Pneumatic connections: VERSILON PTFE smooth-walled Teflon hose is not recommended for pneumatic plug connections, so use compatible fittings and secure mechanical support at terminations. - Use as guidance: the hoseâs low friction and self-lubricating surface allow it to serve as a mechanical guide for other hoses or rods, but even then provide fixed supports to control alignment and load. In summary: support and guide VERSILON PTFE smooth-walled Teflon hose appropriatelyâuse non-damaging clamps/guides, control bend radii, increase support frequency, address electrostatic risks, and avoid plug-type pneumatic fittings.

Hose PTFE smooth VERSILON PTFE

All products, PTFE hoses/

Additional information

Material	PTFE – teflon and similar
Maximum operating temperature [°C]	200
Minimum operating temperature [°C]	260
Vacuum resistance	no
Standard length [m]	100, 25, 30, 50

Light, semi-transparent hose smooth with PTFE o excellent resistance chemical. intended for low-pressure installations, chemicals, paints, adhesives, fuels liquid and gas, oils, greases, air, gases, water, steam and liquids na base water. used we all types industry. The hose is not antistatic (it does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic push-in fittings. can be used also as mechanical guiding cables or tie rods of regard na low factor friction and self-lubricating properties PTFE. Flame-retardant (UL94 V-0) and with a high oxygen index (LOI). factor safety n = 4:1. pressure bursting and working hose, decreases in temperature use above 20°C and is dependent od jej the height. Material hose: smooth PTFE (teflon). hardness Shore (D): 58. temperature use: from -200°C to +260°C. pressure working: od 2.3 bar for 10.8 bar – depending on diameter hose.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
VE-CHEMPTFE-02X03	Hose VERSILON PTFE 2x3 mm	2	8.3	In stock	Enquiry
VE-CHEMPTFE-02X04	Hose VERSILON PTFE 2x4 mm	2	14	In stock	Enquiry
VE-CHEMPTFE-03X04	Hose VERSILON PTFE 3x4 mm	3	5.7	In stock	Enquiry
VE-CHEMPTFE-03X05	Hose VERSILON PTFE 3x5 mm	3	10.8	In stock	Enquiry
VE-CHEMPTFE-04X05	Hose VERSILON PTFE 4x5 mm	4	4.9	In stock	Enquiry
VE-CHEMPTFE-04X06	Hose VERSILON PTFE 4x6 mm	4	8.5	In stock	Enquiry
VE-CHEMPTFE-05X06	Hose VERSILON PTFE 5x6 mm	5	3.8	In stock	Enquiry
VE-CHEMPTFE-05X07	Hose VERSILON PTFE 5x7 mm	5	7.3	In stock	Enquiry
VE-CHEMPTFE-06X07	Hose VERSILON PTFE 6x7 mm	6	3.1	In stock	Enquiry
VE-CHEMPTFE-06X08	Hose VERSILON PTFE 6x8 mm	6	6.3	In stock	Enquiry
VE-CHEMPTFE-08X10	Hose VERSILON PTFE 8x10 mm	8	4.8	In stock	Enquiry
VE-CHEMPTFE-10X12	Hose VERSILON PTFE 10x12 mm	10	4.3	In stock	Enquiry
VE-CHEMPTFE-12X14	Hose VERSILON PTFE 12x14 mm	12	3.5	In stock	Enquiry
VE-CHEMPTFE-14X16	Hose VERSILON PTFE 14x16 mm	14	2.8	In stock	Enquiry
VE-CHEMPTFE-16X18	Hose VERSILON PTFE 16x18 mm	16	2.5	In stock	Enquiry
VE-CHEMPTFE-18X20	Hose VERSILON PTFE 18x20 mm	18	2.3	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Light, semi-transparent hose smooth with PTFE o excellent resistance chemical. intended for low-pressure installations, chemicals, paints, adhesives, fuels liquid and gas, oils, greases, air, gases, water, steam and liquids na base water. used we all types industry. The hose is not antistatic (it does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic push-in fittings. can be used also as mechanical guiding cables or tie rods of regard na low factor friction and self-lubricating properties PTFE. Flame-retardant (UL94 V-0) and with a high oxygen index (LOI). factor safety n = 4:1. pressure bursting and working hose, decreases in temperature use above 20°C and is dependent od jej the height. Material hose: smooth PTFE (teflon). hardness Shore (D): 58. temperature use: from -200°C to +260°C. pressure working: od 2.3 bar for 10.8 bar – depending on diameter hose.

Additional information

Material	PTFE – teflon and similar
Maximum operating temperature [°C]	200
Minimum operating temperature [°C]	260
Vacuum resistance	no
Standard length [m]	100, 25, 30, 50