Is the CAMLOCK E connector plug with corrugated hose end, stainless steel (AISI 316) suitable for handling fuels and petrochemical products at up to 10 bar?

Yes. The CAMLOCK E connector plug with corrugated hose end, stainless steel is suitable for handling fuels and petrochemical products at up to 10 bar. It is made of AISI 316 stainless steel (chemical resistance appropriate for many fuels and petrochemical fluids), built to the MIL-C-27487 (A-A-59326) standard, and its specified working pressure is up to 10 bar depending on connector size. Ensure compatibility with the specific fluid, temperature range and connector size selected, and follow applicable safety and certification requirements for your installation.

Can the CAMLOCK E connector plug with corrugated hose end, stainless steel, be used in cryogenic or high-temperature petrochemical applications?

The CAMLOCK E connector plug with corrugated hose end, stainless steel is made of AISI 316 and built to MIL-C-27487 (A-A-59326) for petrochemical transfer use, with working pressure up to 10 bar (size-dependent). AISI 316 offers good corrosion and moderate temperature resistance, but the description gives no cryogenic temperature ratings or high-temperature limits, nor details on seals or gasket materials. Therefore you cannot assume suitability for cryogenic service or elevated-temperature petrochemical applications without manufacturer confirmation of tested temperature range and compatible sealing materials. For cryogenic or high-temperature use, request certified temperature ratings, material tempering data, and compatible gasket/fluid ratings from the supplier or choose components explicitly rated for those extremes.

What maintenance is required for the CAMLOCK E connector plug with corrugated hose end, stainless steel to ensure 10 bar reliability?

To ensure reliable operation at up to 10 bar for the CAMLOCK E connector plug with corrugated hose end, stainless steel, perform the following maintenance steps regularly: 1. Visual inspection before each use - Check body, cam arms and pins for cracks, deformation, corrosion or heavy wear. - Inspect the corrugated (ribbed) hose end for dents, splits or damage that could compromise seal or fit. - Verify cam arms move smoothly and fully engage/disengage. 2. Seal and gasket care - Inspect the gasket (rubber/EPDM/Viton as used) for cuts, hardening, compression set or swelling. - Replace the gasket immediately if any damage or loss of elasticity is found; use the correct material compatible with transferred media and AISI 316 body. - Keep replacement gaskets on hand sized to the connector. 3. Fasteners and locking components - Check pins, springs and locking clips for corrosion, wear or loosening; replace worn items. - Ensure cam arm pivot pins are secure and lubricated where appropriate. 4. Cleaning and corrosion prevention - Clean internal surfaces and crevices after each service cycle or if exposed to corrosive media. Use compatible cleaning agents that do not attack AISI 316 or gasket material. - Rinse thoroughly and dry to prevent contamination and corrosion. - For aggressive environments, apply a light film of approved anti-seize or corrosion inhibitor on external surfaces (avoid contaminating gasket sealing faces). 5. Functional pressure checks - Periodically perform a pressure leak test at working pressure (up to 10 bar) after reassembly or gasket change to confirm seal integrity. Follow safe test procedures and local regulations. - For high-risk applications, perform scheduled pressure testing according to site QA intervals. 6. Hose end and attachment - Ensure corrugated hose end is properly flared/crimped/clamped to the hose per manufacturer and MIL-A-A-59326 practices. Inspect clamps/crimps for security and corrosion. - Replace hose assemblies showing signs of degradation. 7. Documentation and replacement intervals - Keep a maintenance log noting inspections, parts replaced and pressure tests. - Replace connector if cumulative wear, deformation or repeated repairs could jeopardize 10 bar reliability. 8. Use and storage best practices - Avoid side loads, impacts and improper mating that can damage sealing faces or cams. - Store dry, protected from chemicals and extreme temperatures; keep gaskets separately in cool, dark conditions. Following these steps with correct spare parts and compatible gasket materials will help maintain the CAMLOCK E connector plug with corrugated hose end, stainless steel at reliable performance up to 10 bar.

Plug coupling CAMLOCK E with a serrated hose fitting, steel stainless

Additional information

Material	SS – stainless steel

Plug coupling CAMLOCK E with a serrated hose fitting made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar, depending on the coupling size. Material: steel AISI 316.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AC-E-050-SS	Coupling CAMLOCK E 1/2", AISI 316	12	10	In stock	Enquiry
AC-E-050-SSX	Coupling CAMLOCK E 1/2", AISI 316	12	10	In stock	Enquiry
AC-E-075-SS	Coupling CAMLOCK E 3/4", AISI 316	20	10	In stock	Enquiry
AC-E-075-SSX	Coupling CAMLOCK E 3/4", AISI 316	20	10	In stock	Enquiry
AC-E-100-SS	Coupling CAMLOCK E 1", AISI 316	25	10	In stock	Enquiry
AC-E-100-SSX	Coupling CAMLOCK E 1", AISI 316	25	10	In stock	Enquiry
AC-E-125-SS	Coupling CAMLOCK E 1.1/4", AISI 316	32	10	In stock	Enquiry
AC-E-125-SSX	Coupling CAMLOCK E 1.1/4", AISI 316	32	10	In stock	Enquiry
AC-E-150-SS	Coupling CAMLOCK E 1.1/2", AISI 316	40	10	In stock	Enquiry
AC-E-150-SSX	Coupling CAMLOCK E 1.1/2", AISI 316	40	10	In stock	Enquiry
AC-E-200-SS	Coupling CAMLOCK E 2", AISI 316	50	10	In stock	Enquiry
AC-E-200-SSX	Coupling CAMLOCK E 2", AISI 316	50	10	In stock	Enquiry
AC-E-250-SS	Coupling CAMLOCK E 2.1/2", AISI 316	65	10	In stock	Enquiry
AC-E-250-SSX	Coupling CAMLOCK E 2.1/2", AISI 316	65	10	In stock	Enquiry
AC-E-300-SS	Coupling CAMLOCK E 3", AISI 316	75	10	In stock	Enquiry
AC-E-300-SSX	Coupling CAMLOCK E 3", AISI 316	75	10	In stock	Enquiry
AC-E-400-SS	Coupling CAMLOCK E 4", AISI 316	100	10	In stock	Enquiry
AC-E-400-SSX	Coupling CAMLOCK E 4", AISI 316	100	10	In stock	Enquiry
AC-E-500-SS	Coupling CAMLOCK E 5", AISI 316	125	9	In stock	Enquiry
AC-E-500-SSX	Coupling CAMLOCK E 5", AISI 316	125	9	In stock	Enquiry
AC-E-600-SS	Coupling CAMLOCK E 6", AISI 316	150	9	In stock	Enquiry
AC-E-600-SSX	Coupling CAMLOCK E 6", AISI 316	150	9	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Plug coupling CAMLOCK E with a serrated hose fitting made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar, depending on the coupling size. Material: steel AISI 316.