Does the STOP STP-U brass pneumatic shut-off valve with GW check valve require a specific orientation for correct operation and sealing?

The STOP STP-U brass pneumatic shut-off valve with GW check valve does require correct orientation for proper operation and sealing. As a safety shut-off installed on an actuatorâs supply port, it must be fitted so that the check valve and internal flow path align with the intended direction of the control signal: supply air must enter the valveâs designated inlet and exit toward the actuator. Incorrect orientation (reverse installation) can prevent the valve from allowing airflow when the pneumatic control signal is present, compromise the check-valve function, and may lead to leakage or failure to stop the actuator when control pressure drops. Additionally, ensure thread sealing and torque are correct for the NBR seals and nickel-plated brass body to achieve reliable sealing within the stated operating pressure (0.5â10 bar) and temperature range (â10 Â°C to +60 Â°C).

Can the STOP STP-U brass pneumatic shut-off valve with GW check valve handle media other than compressed air without performance loss?

STOP STP-U brass pneumatic shut-off valve with GW check valve is designed and specified for pneumatic service (compressed air) with NBR seals, operating 0.5â10 bar and â10Â°C to +60Â°C. Using media other than compressed air (e.g. gases with oils, aggressive gases, vacuum, or liquids) can degrade NBR sealing, corrode or swell components, change leakage and response, and impair the GW check valve function. Nickelâplated brass resists many but not all fluids; compatibility must be checked per specific media, pressure and temperature. Conclusion: it is intended for compressed air-using other media risks performance loss unless manufacturer confirms compatibility for the exact fluid and conditions.

Is the STOP STP-U brass pneumatic shut-off valve with GW check valve suitable for vacuum service?

No. the STOP STP-U brass pneumatic shut-off valve with GW check valve is not suitable for vacuum service. It is designed and specified for pneumatic (positive) pressure operation in the range 0.5 Ã· 10 bar and operates by allowing airflow only when a control pressure is present; it stops the actuator after a drop in control pressure. Its specifications (minimum operating pressure 0.5 bar), sealing (NBR), and internal design for check-valve function do not guarantee reliable sealing or controlled flow under vacuum or negative pressure conditions. Using it in vacuum service risks leakage, improper operation, and possible damage; select a valve explicitly rated for vacuum if vacuum operation is required.

Valve shut-off pneumatic brass alloy STP-U with valve check female

All products, Pneumatic valves/

Additional information

Material	B – brass (bronze)

Valve shut-off alloy series STP-U with valve check with a thread internal used mainly as safety valve. When mounted on the supply connections of the actuator, it allows air flow only in the presence of a pneumatic control signal. The actuator is stopped after a drop in the control pressure. pressure working: 0.5 ÷ 10 bar. Operating temperature: from -10°C to +60°C. Material the body: brass nickel-plated. Sealing: NBR.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-W6001001001	Valve STOP with a valve check STP-U, 1/8" female / 1/8" male, pilot M5 female	-	10	In stock	Enquiry
MW-W6001011011	Valve STOP with a valve check STP-U, 1/4" female / 1/4" male, pilot 1/8" female	-	10	In stock	Enquiry
MW-W6001021021	Valve STOP with a valve check STP-U, 3/8" female / 3/8" male, pilot 1/8" female	-	10	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Valve shut-off alloy series STP-U with valve check with a thread internal used mainly as safety valve. When mounted on the supply connections of the actuator, it allows air flow only in the presence of a pneumatic control signal. The actuator is stopped after a drop in the control pressure. pressure working: 0.5 ÷ 10 bar. Operating temperature: from -10°C to +60°C. Material the body: brass nickel-plated. Sealing: NBR.