Can the Multi-output distribution strip with 1/4" outputs, aluminum handle 12 bar pressure and -10Â°C to +80Â°C operating temperature safely in my pneumatic system?

Yes . the Multi-output distribution strip with 1/4" outputs, aluminum (working pressure 12 bar; operating temperature -10Â°C to +80Â°C; anodized aluminum) can be safely used in a pneumatic system provided the following conditions are met: - System pressure does not exceed 12 bar (use a pressure regulator or relief valve if upstream pressure can be higher). - Ambient and media temperatures stay within -10Â°C to +80Â°C. - The 1/4" outlets and connected fittings/hose/tubing are rated for â¥12 bar and compatible with the stripâs thread/type to avoid leaks. - Proper mechanical mounting is used with the provided additional holes to prevent vibration or movement that could stress connections. - Appropriate sealing (PTFE tape or thread sealant) and correct torque are applied to threaded connections. - The compressed air is free of contaminants (water, oil, particulates) or adequate filtration/drying is installed to avoid corrosion or clogging. - Consider system safety features (shut-off valves, pressure relief) and periodic inspection for wear, corrosion or leaks. If any of these conditions are not met (higher pressure, out-of-range temperature, incompatible fittings or contaminated air), do not use the Multi-output distribution strip with 1/4" outputs, aluminum until the issues are resolved.

Is the Multi-output distribution strip with 1/4" outputs, aluminum suitable for outdoor installations at -10Â°C?

Yes. The Multi-output distribution strip with 1/4" outputs, aluminum is rated for an operating temperature range from -10Â°C to +80Â°C and is made of anodized aluminum, making it suitable for outdoor installations at -10Â°C. Ensure any fittings, seals, and mounting hardware used are also rated for low temperatures and outdoor exposure to maintain system integrity.

Does the Multi-output distribution strip with 1/4" outputs, aluminum require specific mounting hardware for secure installation?

Does the Multi-output distribution strip with 1/4" outputs, aluminum require specific mounting hardware for secure installation? The Multi-output distribution strip with 1/4" outputs, aluminum includes additional holes for securing it in the desired installation location. These holes allow you to fasten the strip using common mounting hardware (e.g., screws or bolts) appropriate for the installation surface and load. Because the strip is made of anodized aluminum and is intended for pneumatic systems operating up to 12 bar and temperatures from -10Â°C to +80Â°C, choose corrosion-resistant fasteners (stainless steel or zinc-plated) and suitable anchors if mounting to masonry or hollow walls. Select screw size and type compatible with the stripâs hole diameter and the substrate; if vibration or dynamic loads are expected, use locking washers or threadlocker for added security. In summary: no proprietary or special mounting hardware is required, but use appropriate, corrosion-resistant fasteners and anchors sized for the stripâs holes and the mounting surface to ensure a secure installation.

Multi-output distribution manifold with 1/4″ outlets, aluminum

Accessories for pneumatic fittings, All products/

Additional information

Material	AL – aluminum

Multi-output distribution manifold with 1/4″ outlets for use in pneumatic systems, allowing pressurized compressed air to be split into several branches. It has additional holes for fixing it at the desired point of the installation. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: anodized aluminum.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-W0502121006	Distribution manifold, 2 x inlet 3/8" BSP female, 3 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0502121008	Distribution manifold, 2 x inlet 3/8" BSP female, 4 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0502121010	Distribution manifold, 2 x inlet 3/8" BSP female, 5 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0502121012	Distribution manifold, 2 x inlet 3/8" BSP female, 6 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0502131006	Distribution manifold, 2 x inlet 1/2" BSP female, 3 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0502131008	Distribution manifold, 2 x inlet 1/2" BSP female, 4 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0502131010	Distribution manifold, 2 x inlet 1/2" BSP female, 5 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry
MW-W0502131012	Distribution manifold, 2 x inlet 1/2" BSP female, 6 x outlet 1/4" BSP female, aluminum	-	12	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Multi-output distribution manifold with 1/4″ outlets for use in pneumatic systems, allowing pressurized compressed air to be split into several branches. It has additional holes for fixing it at the desired point of the installation. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: anodized aluminum.