Is the Single swivel connector, brass suitable for continuous use at 12 bar and within the -10Â°C to +80Â°C temperature range?

Yes. Based on the provided description, the Single swivel connector, brass is specified for a working pressure of 12 bar and an operating temperature range from -10Â°C to +80Â°C. Made of nickel-plated brass, it is therefore suitable for continuous use within those exact pressure and temperature limits. Ensure that application-specific factors (media compatibility, duty cycle, vibration, cyclic pressure changes, and sealing components) do not introduce additional constraints beyond the listed specifications. If such factors are present, verify with the manufacturer or technical datasheet for long-term continuous-service recommendations.

Can the Single swivel connector, brass withstand corrosion in humid environments at 12 bar and -10Â°C to +80Â°C?

Single swivel connector, brass (nickel-plated brass) offers good general corrosion resistance and is suitable for many humid environments within the stated operating range (â10Â°C to +80Â°C) and working pressure of 12 bar. Nickel plating improves surface hardness and provides a protective barrier against mild corrosion and wear. However, long-term resistance depends on environment aggressiveness: in freshwater or typical indoor/outdoor humid conditions it should perform well; in highly corrosive atmospheres (chlorides, salt spray, acidic/alkaline fumes) nickel-plated brass may eventually corrode or suffer dezincification. For prolonged exposure to marine or chemical environments, consider more corrosion-resistant materials or additional protective coatings.

Does the Single swivel connector, brass require special sealing materials for reliable operation at 12 bar and -10Â°C to +80Â°C?

Generally no, the Single swivel connector, brass does not require special sealing materials beyond standard thread sealants when used at 12 bar and -10Â°C to +80Â°C. provided you use compatible, commonly recommended seals and install it correctly. Details: - Material and ratings: The connector is nickel-plated brass rated to 12 bar and â10Â°C to +80Â°C, which are moderate pressure and temperature conditions well within the capability of typical sealing compounds and PTFE tape. - Typical seals: For threaded connections common, reliable choices are PTFE (thread) tape or a general-purpose anaerobic thread sealant (pipe dope) compatible with brass and the media. If the joint uses an internal/external thread interface with a metal-to-metal seat, a simple thread sealant or tape is usually sufficient. - Media compatibility: Choose the sealant based on the conveyed fluid (water, air, oil, steam, chemicals). For water and air, PTFE tape or standard pipe dope is fine. For aggressive chemicals, fuels or certain oils, use a sealant explicitly compatible with those media. - Temperature suitability: Standard PTFE tape and most general-purpose pipe dopes cover the â10Â°C to +80Â°C range. If you expect frequent cycling to extremes or prolonged exposure near limits, select a sealant rated for those temperatures. - Mechanical factors: Ensure proper torque and avoid over-tightening to prevent thread damage. For dynamic/rotating joints, consider whether the rotating interface is sealed internally by the joint design; additional external thread sealing won't affect the internal rotary seal. - When special seals are needed: If the application involves vacuum, hazardous/regulated fluids, high purity, extreme temperatures beyond the stated range, or where leak-tightness beyond normal pipe practice is required, you may need specialized sealants, O-rings, or PTFE-packed joints. Recommendation: Use PTFE tape or a compatible pipe sealant rated for your fluid and the â10Â°C to +80Â°C range. If unsure about the media or if you require absolute leak-tightness, consult the manufacturerâs datasheet or technical support for recommended sealing methods for the Single swivel connector, brass.

Single swivel joint, brass

Accessories for pneumatic fittings, All products/

Additional information

Material	B – brass (bronze)

Single swivel joint terminated with a male thread on one side and a female thread on the other. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: nickel-plated brass.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-W0511101101	Coupling obrotowe, 1/8" BSP female x 1/8" BSP female, brass niklowany	-	12	In stock	Enquiry
MW-W0511121121	Coupling obrotowe, 1/4" BSP female x 1/4" BSP female, brass niklowany	-	12	In stock	Enquiry
MW-W0511131131	Coupling obrotowe, 3/8" BSP female x 3/8" BSP female, brass niklowany	-	12	In stock	Enquiry
MW-W0511141141	Coupling obrotowe, 1/2" BSP female x 1/2" BSP female, brass niklowany	-	12	In stock	Enquiry
MW-W0511151151	Coupling obrotowe, 3/4" BSP female x 3/4" BSP female, brass niklowany	-	12	In stock	Enquiry
MW-W0511161161	Coupling obrotowe, 1" BSP female x 1" BSP female, brass niklowany	-	12	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Single swivel joint terminated with a male thread on one side and a female thread on the other. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: nickel-plated brass.