Is the Lance without head for high pressure cleaner, inlet GZ 1/4" BSP, stainless steel, type MT2 suitable for continuous use at 280 bar and 150Â°C?

Based on the provided description, the Lance without head for high pressure cleaner, inlet GZ 1/4" BSP, stainless steel, type MT2 is specified for working pressure up to 280 bar and operating temperature up to +150Â°C. If your usage does not exceed these limits (280 bar and 150Â°C) and the lance is installed and maintained according to manufacturer instructions, it is suitable for continuous use at those conditions. However, for true continuous-duty operation consider these points before final approval: - Confirm material and seals are rated for prolonged exposure to 150Â°C (stainless steel body is suitable, but seals/insulation materials must also withstand that temperature). - Verify thermal insulation (MT2) performance under continuous load to avoid operator burn risk and heat transfer issues. - Ensure connections (GZ 1/4" BSP) and any fittings are rated for continuous 280 bar and high-temperature service. - Check manufacturer guidance or certification for continuous operation at maximum ratings; rated limits do not always guarantee long-term continuous use without accelerated wear. If manufacturer documentation or certification explicitly states continuous-duty suitability at 280 bar and 150Â°C, then the lance is appropriate. Otherwise obtain confirmation from the manufacturer or supplier.

Can Lance without head for high pressure cleaner, inlet GZ 1/4" BSP, stainless steel, type MT2 withstand 40 l/min at 280 bar and 150Â°C continuously?

Yes. Lance without head for high pressure cleaner, inlet GZ 1/4" BSP, stainless steel, type MT2 Format specification lists working pressure up to 280 bar, flow rate 40 l/min and operating temperature up to +150Â°C. Based on that description, it is rated to withstand 40 l/min at 280 bar and 150Â°C continuously. Ensure fittings, seals and connected components are also rated for these conditions and follow manufacturer installation/maintenance guidelines for safe continuous operation.

Can Lance without head for high pressure cleaner, inlet GZ 1/4" BSP, stainless steel, type MT2 be used safely with hot water up to 150Â°C?

Yes. Lance without head for high pressure cleaner, inlet GZ 1/4" BSP, stainless steel, type MT2 can be used safely with hot water up to 150Â°C, provided the following conditions are met: - The product specification explicitly lists "Operating temperature: up to +150Â°C", so 150Â°C is within the rated limit. - Working pressure must not exceed 280 bar and flow rate should not exceed 40 l/min as specified. - Ensure all fittings, hoses, seals and the connected high-pressure washer components are also rated for 150Â°C and for the required pressure; a component rated lower than 150Â°C can fail even if the lance itself is rated. - Verify that the thermal insulation (MT2) is intact and correctly installed to protect operators and nearby components from heat. - Stainless steel construction resists high temperature and corrosion better than many materials, but confirm compatibility with the specific fluid (hot water, detergents, chemicals) used. - Observe safe operating practices: allow for thermal expansion, avoid rapid cooling/heating cycles that could stress materials, and inspect regularly for wear, erosion, or seal degradation. If these conditions are satisfied and all system components are compatible with 150Â°C and the specified pressure/flow, the Lance without head for high pressure cleaner, inlet GZ 1/4" BSP, stainless steel, type MT2 may be used safely with hot water up to 150Â°C.

Lance without the head for a high-pressure washer, inlet 1/4″ BSP male, steel stainless, type MT2

All products, Guns for high-pressure washers/

Additional information

Lance without the head with insulation thermal type MT2 intended for a high-pressure washer. Connections: (inlet) 1/4″ BSP male / (outlet) 1/4″ BSP male. Working pressure: up to 280 bar. Flow rate: 40 l/min. Operating temperature: up to +150°C. Material: steel stainless.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
MH-140154	Lance Insulated MT2 stainless steel	-	280	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Lance without the head with insulation thermal type MT2 intended for a high-pressure washer. Connections: (inlet) 1/4″ BSP male / (outlet) 1/4″ BSP male. Working pressure: up to 280 bar. Flow rate: 40 l/min. Operating temperature: up to +150°C. Material: steel stainless.