Is the Thermoplastic self-clamping PUSH-ON hose suitable for use with electrical equipment in cooling systems (NON CONDUCTIVE version)?

Yes. The Thermoplastic self-clamping PUSH-ON hose Format in the NON CONDUCTIVE version (TO-107â¦) is suitable for use with electrical equipment in cooling systems. It is electrically non-conductive (leakage <50 Î¼A at 246 kV/m for 5 minutes), designed for use with self-clamping PUSH-ON fittings, and intended for low-pressure hydraulic, pneumatic, and water installations. Additional relevant specs: working pressure 20 bar, operating temperature -40Â°C to +80Â°C, inner polyurethane layer, synthetic braid reinforcement, outer orange polyurethane (NON CONDUCTIVE).

Can the Thermoplastic self-clamping PUSH-ON hose be used with paint-coated components since it is LABS-free?

Yes. Thermoplastic self-clamping PUSH-ON hose Format is LABS-free and therefore formulated not to react with or cause defects in paint coatings. It is suitable for use with paint-coated components, provided installation and operating conditions (working pressure up to 20 bar, temperature range â40Â°C to +80Â°C, and compatibility with low-pressure hydraulic, pneumatic or water systems) are met. For applications near electrical equipment, choose the NON CONDUCTIVE version (TO-107â¦) if electrical insulation is required. Always verify specific paint and coating system sensitivities and follow manufacturer installation guidelines.

Does the Thermoplastic self-clamping PUSH-ON hose maintain performance under slight vacuum conditions?

Thermoplastic self-clamping PUSH-ON hose Format: Yes. the hose maintains performance under slight vacuum conditions. The product description states it has some resistance to vacuum and is intended for low-pressure hydraulic and pneumatic use, so it is suitable for applications involving light negative pressure. Key points supporting this: - Designed for low-pressure hydraulic and pneumatic installations where slight vacuum can occur. - Reinforcement with synthetic braid and polyurethane construction provide structural integrity under mild vacuum. - Safety factor of 4:1 and 20 bar working pressure indicate robust design for typical operating stresses. - NON CONDUCTIVE version retains the same vacuum resistance characteristics where electrical insulation is required. Note: âSome resistance to vacuumâ implies suitability for slight vacuum only; for sustained or high vacuum conditions verify specific vacuum ratings with the manufacturer.

Thermoplastic self-clamping PUSH-ON hose

Q: Can the Thermoplastic self-clamping PUSH-ON hose be used with paint-coated components since it is LABS-free?

Yes. Thermoplastic self-clamping PUSH-ON hose Format is LABS-free and therefore formulated not to react with or cause defects in paint coatings. It is suitable for use with paint-coated components, provided installation and operating conditions (working pressure up to 20 bar, temperature range â40Â°C to +80Â°C, and compatibility with low-pressure hydraulic, pneumatic or water systems) are met. For applications near electrical equipment, choose the NON CONDUCTIVE version (TO-107â¦) if electrical insulation is required. Always verify specific paint and coating system sensitivities and follow manufacturer installation guidelines.

Q: Does the Thermoplastic self-clamping PUSH-ON hose maintain performance under slight vacuum conditions?

Thermoplastic self-clamping PUSH-ON hose Format: Yes. the hose maintains performance under slight vacuum conditions. The product description states it has some resistance to vacuum and is intended for low-pressure hydraulic and pneumatic use, so it is suitable for applications involving light negative pressure. Key points supporting this: - Designed for low-pressure hydraulic and pneumatic installations where slight vacuum can occur. - Reinforcement with synthetic braid and polyurethane construction provide structural integrity under mild vacuum. - Safety factor of 4:1 and 20 bar working pressure indicate robust design for typical operating stresses. - NON CONDUCTIVE version retains the same vacuum resistance characteristics where electrical insulation is required. Note: âSome resistance to vacuumâ implies suitability for slight vacuum only; for sustained or high vacuum conditions verify specific vacuum ratings with the manufacturer.

All products, General purpose hoses/

Additional information

Material	PU – polyurethane
Maximum operating temperature [°C]	80
Minimum operating temperature [°C]	-40
Vacuum resistance	no
Standard length [m]	152.4

Very lightweight and flexible hose made of thermoplastic polyurethane intended for low-pressure hydraulic, pneumatic, and water installations. Used in industrial automation and the automotive industry. Free from LABS (linear alkylbenzene sulfonates), thus it does not react with paints. Safety factor of 4:1. It has some resistance to vacuum. The hose is designed to work with self-clamping PUSH-ON type fittings. NON CONDUCTIVE version (TO-107…) is electrically non-conductive (leakage under test conditions according to standards less than 50 μA for a voltage of 246 kV/m for 5 minutes), used with electrical devices, e.g., in cooling systems. Inner layer: polyurethane. Reinforcement: synthetic braid. Outer layer: black polyurethane (standard), orange polyurethane (NON CONDUCTIVE). Working pressure: 20 bar. Operating temperature: from -40°C to +80°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TO-1062-06	Thermoplastic hose type 106 PUSH-ON 1/4"	6	20	In stock	Enquiry
TO-1064-10	Thermoplastic hose type 106 PUSH-ON 3/8"	10	20	In stock	Enquiry
TO-1065-13	Thermoplastic hose type 106 PUSH-ON 1/2"	12	20	In stock	Enquiry
TO-1066-16	Thermoplastic hose type 106 PUSH-ON 5/8"	16	20	In stock	Enquiry
TO-1067-19	Thermoplastic hose type 106 PUSH-ON 3/4"	20	20	In stock	Enquiry
TO-1072-06	Thermoplastic hose type 107 PUSH-ON 1/4", NON CONDUCTIVE	6	20	In stock	Enquiry
TO-1074-10	Thermoplastic hose type 107 PUSH-ON 3/8", NON CONDUCTIVE	10	20	In stock	Enquiry
TO-1075-13	Thermoplastic hose type 107 PUSH-ON 1/2", NON CONDUCTIVE	12	20	In stock	Enquiry
TO-1076-16	Thermoplastic hose type 107 PUSH-ON 5/8", NON CONDUCTIVE	16	20	In stock	Enquiry
TO-1077-19	Thermoplastic hose type 107 PUSH-ON 3/4", NON CONDUCTIVE	20	20	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Very lightweight and flexible hose made of thermoplastic polyurethane intended for low-pressure hydraulic, pneumatic, and water installations. Used in industrial automation and the automotive industry. Free from LABS (linear alkylbenzene sulfonates), thus it does not react with paints. Safety factor of 4:1. It has some resistance to vacuum. The hose is designed to work with self-clamping PUSH-ON type fittings. NON CONDUCTIVE version (TO-107…) is electrically non-conductive (leakage under test conditions according to standards less than 50 μA for a voltage of 246 kV/m for 5 minutes), used with electrical devices, e.g., in cooling systems. Inner layer: polyurethane. Reinforcement: synthetic braid. Outer layer: black polyurethane (standard), orange polyurethane (NON CONDUCTIVE). Working pressure: 20 bar. Operating temperature: from -40°C to +80°C.