Is the SAE 3000 90Â° flange end, type ZSK211, light series, carbon steel, zinc-nickel suitable for crimping with our hoseâs specified crimping sleeve?

Yes . the SAE 3000 90Â° flange end, type ZSK211, light series, carbon steel, zinc-nickel is suitable for crimping with your hoseâs specified crimping sleeve, provided your sleeve is rated for the same hose type and size. The product description explicitly states it is "designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type." Material and coating (carbon steel with 6â10 Âµm zincânickel) do not impede crimping and offer high corrosion resistance, but confirm these points before crimping: - Confirm sleeve dimensions and pressure rating match the hose and ZSK211 flange end (hose ID, crimp diameter, and crimp profile). - Verify compatibility of crimping machine/settings with this flange end and hose assembly. - Ensure the crimping sleeve is approved for the hose construction (reinforcement layers) and working pressure (SAE 3000 series rating). If those checks pass, the ZSK211 light series flange end is appropriate for crimping with your specified sleeve.

Can SAE 3000 90Â° flange end, type ZSK211, light series, carbon steel, zinc-nickel be used with different crimping sleeves than specified by the hose manufacturer?

No - SAE 3000 90Â° flange end, type ZSK211, light series, carbon steel, zinc-nickel must be crimped using a crimping sleeve specified for the hose type. The product is designed for crimping in hydraulic and industrial hoses with a sleeve matched to hose dimensions, material and pressure rating; using a different or nonâspecified sleeve risks improper crimp integrity, leaks, premature failure and voiding of safety/performance requirements. Maintain manufacturerârecommended sleeve type and crimping procedure to ensure correct mechanical fit and the corrosionâresistant coating performance.

Can SAE 3000 90Â° flange end, type ZSK211, light series, carbon steel, zinc-nickel withstand high-pressure hydraulic cycling without leaks?

Yes. with proper crimping, hose compatibility and installation, the SAE 3000 90Â° flange end, type ZSK211, light series, carbon steel, zinc-nickel can withstand highâpressure hydraulic cycling without leaks; however, performance depends on several critical conditions. Key points to ensure leakâfree highâpressure cycling: - Correct application: The fitting is designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Use the exact sleeve and crimp dimensions recommended by the hose and fitting manufacturers. - Hose compatibility: Match the SAE 3000 pressure class and hose construction (reinforcement layers, inner tube) to the intended system pressure and cyclic load. The assembly must be rated for the peak and dynamic pressures you will apply. - Crimp quality: Proper tooling, calibrated crimp machine, correct die profile and crimp depth are essential. Poor or inconsistent crimps are the most common cause of leaks under cycling. - Seal and surface considerations: Carbon steel body with 6â10 Âµm zincânickel coating offers very high corrosion resistance (up to ~720 hours salt spray) which helps maintain sealing surfaces in corrosive environments. However, electrochemical compatibility with hydraulic fluid and mating components should be verified. - Installation and system factors: Correct torque on mating flanges/adapters, proper hose routing (avoid excessive bend radii, twist, abrasion), and preventing pressure spikes will extend life under cycling. - Testing and validation: Validate assemblies with burst, impulse/cycling and leak tests per relevant standards (e.g., SAE J517/J512 or customer specs). Periodic inspection under service conditions is recommended. Conclusion: Mechanically and corrosionâresistanceâwise the SAE 3000 90Â° flange end, type ZSK211, light series, carbon steel, zinc-nickel is suitable for highâpressure hydraulic cycling when assembled and installed correctly and when matched to appropriate hoses and system conditions. Failure to follow crimping, compatibility, or installation requirements may lead to leaks.

SAE 3000 90° flange end, type ZSK211, light series, carbon steel, zinc-nickel

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)
Standard length [m]	10, 2

SAE 3000 flange end (SFL), 90° angled, lightweight series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Surface coated with zinc-nickel with a layer thickness of 6-10 µm, characterized by very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZSK211-08-08-CN	End fitting 90° SAE 1/2", hose 1/2", lightweight, Zn-Ni	12	350	In stock	Enquiry
TI-ZSK211-12-08-CN	End fitting 90° SAE 3/4", hose 1/2", lightweight, Zn-Ni	12	350	In stock	Enquiry
TI-ZSK211-12-10-CN	End fitting 90° SAE 3/4", hose 5/8", lightweight, Zn-Ni	16	350	In stock	Enquiry
TI-ZSK211-12-12-CN	End fitting 90° SAE 3/4", hose 3/4", lightweight, Zn-Ni	20	350	In stock	Enquiry
TI-ZSK211-16-12-CN	End fitting 90° SAE 1", hose 3/4", lightweight, Zn-Ni	20	280	In stock	Enquiry
TI-ZSK211-16-16-CN	End fitting 90° SAE 1", hose 1", lightweight, Zn-Ni	25	280	In stock	Enquiry
TI-ZSK211-20-16-CN	End fitting 90° SAE 1.1/4", hose 1", lightweight, Zn-Ni	25	280	In stock	Enquiry
TI-ZSK211-20-20-CN	End fitting 90° SAE 1.1/4", hose 1.1/4", lightweight, Zn-Ni	32	210	In stock	Enquiry
TI-ZSK211-24-20-CN	End fitting 90° SAE 1.1/2", hose 1.1/4", lightweight, Zn-Ni	32	210	In stock	Enquiry
TI-ZSK211-24-24-CN	End fitting 90° SAE 1.1/2", hose 1.1/2", lightweight, Zn-Ni	38	185	In stock	Enquiry
TI-ZSK211-32-24-CN	End fitting 90° SAE 2", hose 1.1/2", lightweight, Zn-Ni	38	185	In stock	Enquiry
TI-ZSK211-32-32-CN	End fitting 90° SAE 2", hose 2", lightweight, Zn-Ni	50	175	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

SAE 3000 flange end (SFL), 90° angled, lightweight series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Surface coated with zinc-nickel with a layer thickness of 6-10 µm, characterized by very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.