Is the PERROT lever connector socket with PN 10 flange, carbon steel, KMF suitable for use in wastewater treatment plants and resistant to corrosion after galvanization?

Yes. The PERROT lever connector socket with PN 10 flange, carbon steel, KMF Format is explicitly listed for use in wastewater treatment plants and sewage discharge, so it is suitable for that application. Its construction from carbon steel with galvanization provides baseline corrosion protection appropriate for many wastewater environments. The SBR sealing and a working pressure rating up to 10 bar meet common operational requirements for drainage and wastewater systems. However, suitability depends on specific site conditions: highly aggressive or chemically loaded wastewaters, prolonged immersion in saline/brackish water, or environments with poor maintenance may exceed galvanized carbon steelâs corrosion resistance. For such cases stainless steel or specially coated materials may be preferable. Verify compatibility with the wastewaterâs chemical composition, expected exposure (immersed vs. intermittent), and local regulations. Regular inspection and maintenance will also extend service life.

Can the PERROT lever connector socket with PN 10 flange, carbon steel, KMF be used for groundwater drainage and withstand abrasive solids?

Yes. The PERROT lever connector socket with PN 10 flange, carbon steel, KMF Format is specified for groundwater drainage in its applications list, so it is suitable for that service. It is made of galvanized carbon steel with an SBR seal and rated up to 10 bar, which provides good general corrosion resistance and pressure capability for typical groundwater systems. However, while it will handle normal suspended solids, SBR sealing and carbon steel construction are not specifically optimized for heavy abrasive solids or highly erosive slurry. For continuous exposure to coarse or highly abrasive material, consider abrasion-resistant materials or special liners; otherwise routine inspection and maintenance are recommended.

Does the PERROT lever connector socket with PN 10 flange, carbon steel, KMF require special maintenance after galvanization?

No special maintenance is required for the PERROT lever connector socket with PN 10 flange, carbon steel, KMF after galvanization, provided normal installation and operating conditions are observed. Galvanization gives the carbon steel excellent corrosion resistance for the typical environments listed (agriculture, horticulture, industry, construction, road and tunnel building, groundwater drainage, wastewater treatment, sewage discharge, environmental protection). Basic recommendations: - Inspect visually after installation and periodically in aggressive environments (e.g., high salinity, chemical exposure) to check for coating damage or unusual corrosion. - Avoid mechanical damage to the galvanized coating during handling and assembly; scratched areas can be touched up with suitable cold galvanizing repair paint if needed. - Ensure sealing (SBR) and bolted connections are correctly fitted and checked for leaks; replace seals if degraded. - For prolonged exposure to highly corrosive chemicals or continuous immersion in aggressive media, consult manufacturer for compatibility and consider additional protective measures (e.g., coatings, cathodic protection). - Clean off heavy deposits, debris or chemical residues that could trap moisture and accelerate local corrosion. In standard use up to 10 bar in the environments described, routine visual checks and good installation practice are sufficient; no routine post-galvanization treatment is normally required.

A PERROT lever coupling socket with a flange PN 10, steel carbon, KMF

All products, Lever couplings/

Additional information

Material	CS – steel (cast iron)

A PERROT lever coupling socket with a flange PN 10 with wide application, among others in agriculture, horticulture, industry, construction, road and tunnel building, groundwater drainage, sewage treatment plants, wastewater discharge, and environmental protection. Material: steel carbon, galvanized. Sealing: SBR. Working pressure: up to 10 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HC-KMF-050-050	Socket KMF 50 mm with a flange DN 50, galvanized steel	-	10	In stock	Enquiry
HC-KMF-070-065	Socket KMF 70 mm with a flange DN 65, galvanized steel	-	10	In stock	Enquiry
HC-KMF-089-080	Socket KMF 89 mm with a flange DN 80, galvanized steel	-	10	In stock	Enquiry
HC-KMF-108-100	Socket KMF 108 mm with a flange DN 100, galvanized steel	-	10	In stock	Enquiry
HC-KMF-133-125	Socket KMF 133 mm with a flange DN 125, galvanized steel	-	10	In stock	Enquiry
HC-KMF-159-150	Socket KMF 159 mm with a flange DN 150, galvanized steel	-	10	In stock	Enquiry
HC-KMF-216-200	Socket KMF 216 mm with a flange DN 200, galvanized steel	-	8	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

A PERROT lever coupling socket with a flange PN 10 with wide application, among others in agriculture, horticulture, industry, construction, road and tunnel building, groundwater drainage, sewage treatment plants, wastewater discharge, and environmental protection. Material: steel carbon, galvanized. Sealing: SBR. Working pressure: up to 10 bar.