Can the METRIC (DIN 2353) zinc-nickel plated carbon steel twist-on connector, HOLMBURY type RH, be disconnected under the allowed residual pressure of 50 bar without leakage?

Yes. The METRIC (DIN 2353) zinc-nickel plated carbon steel twist-on connector, HOLMBURY type RH Format is designed for disconnection under a residual pressure of 50 bar without leakage. Its plug is a screw quick coupling with zero leakage and a flat front surface that prevents fluid loss during disconnection. The product specification explicitly states couplings are allowed to be disconnected under a residual pressure of 50 bar for hydraulic oil service, with operating temperature -25Â°C to +100Â°C and working pressures up to 420 bar (size dependent). Ensure the coupling is in good condition, correctly installed, and used within specified limits (safety factor 4:1, rated pressures), and follow manufacturer procedures when disconnecting.

Is the METRIC (DIN 2353) zinc-nickel plated carbon steel twist-on connector, HOLMBURY type RH safe to disconnect under 50 bar residual pressure?

Yes. The METRIC (DIN 2353) zinc-nickel plated carbon steel twist-on connector, HOLMBURY type RH is designed and rated to be disconnected under a residual pressure of 50 bar. The product description explicitly states the coupling is allowed under residual pressure of 50 bar, features a flat front surface to prevent fluid loss during disconnection, and is specified for hydraulic oil service with operating temperature â25Â°C to +100Â°C and working pressures up to 420 bar (size-dependent). Ensure the specific size and installation meet manufacturer instructions and that system conditions (temperature, fluid compatibility, wear/corrosion) are appropriate before performing disconnection.

METRIC (DIN 2353) zinc-nickel plated carbon steel twist-on connector, HOLMBURY type RH

Q: Can METRIC (DIN 2353) zinc-nickel plated carbon steel twist-on connector, HOLMBURY type RH, be used for hydraulic oil up to 420 bar?

Yes. METRIC (DIN 2353) zinc-nickel plated carbon steel twist-on connector, HOLMBURY type RH can be used for hydraulic oil up to 420 bar, with these conditions and limitations: - The product specification states âApplication: hydraulic power (hydraulic oil)â and âWorking pressure: up to 420 bar (depending on the size of the coupling)â, so use at pressures up to 420 bar is within the declared capability for the correct size variant. - Coupling permits residual pressure on disconnection up to 50 bar; do not attempt disconnection if residual system pressure exceeds 50 bar. - Operating temperature range is -25Â°C to +100Â°C; ensure system fluid and environment fall inside this range. - Safety factor is 4:1; verify system design and peak loads comply with this margin. - Material is carbon steel with zinc-nickel coating; confirm compatibility of coating and base material with your hydraulic oil and any environmental/corrosion requirements. - Flow rating is provided for a 3 bar pressure drop; confirm flow/pressure-drop performance meets your application needs. - Ensure you select the correct coupling size variant rated for 420 bar and follow manufacturer installation, maintenance and compatibility instructions. If any of these conditions (size rating, residual-pressure practice, temperature, material compatibility, or safety margin) are not met in your system, do not use the coupling at 420 bar without further validation or an alternative rated component.

All products, Hydraulic quick couplings/

Additional information

Material	CS – steel (cast iron)

Screw quick coupling with zero leakage – plug, type RH, with external metric thread DIN 2353. The flat design of the front surface prevents fluid loss during disconnection. Coupling is allowed under a residual pressure of 50 bar. Application: hydraulic power (hydraulic oil). Material: carbon steel with zinc-nickel coating. Operating temperature: from -25°C to +100°C. Working pressure: up to 420 bar (depending on the size of the coupling). Safety factor 4:1. Flow has been provided for a pressure drop of 3 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HQ-RH08-M-12L	Screw connector RH 3/8", GZ M18x1.5 (12L)	-	420	In stock	Enquiry
HQ-RH12-M-15L	Screw connector RH 1/2", GZ M22x1.5 (15L)	-	420	In stock	Enquiry
HQ-RH12-M-16S	Screw connector RH 1/2", GZ M24x1.5 (16S)	-	420	In stock	Enquiry
HQ-RH20-M-30S	Screw connector RH 3/4", GZ M42x2 (30S)	-	350	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Screw quick coupling with zero leakage – plug, type RH, with external metric thread DIN 2353. The flat design of the front surface prevents fluid loss during disconnection. Coupling is allowed under a residual pressure of 50 bar. Application: hydraulic power (hydraulic oil). Material: carbon steel with zinc-nickel coating. Operating temperature: from -25°C to +100°C. Working pressure: up to 420 bar (depending on the size of the coupling). Safety factor 4:1. Flow has been provided for a pressure drop of 3 bar.