Can the Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3 withstand continuous use at 8.3 bar and -40Â°C to +82Â°C without seal degradation?

Yes . based on the provided specifications, the Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3 can operate continuously at 8.3 bar and in the temperature range â40Â°C to +82Â°C without expected seal degradation, provided normal conditions and correct installation. Reasons: - Working pressure is specified âup to 8.3 bar,â so continuous operation at 8.3 bar is at the upper rated limit and within the productâs rated capability. - Operating temperature range is specified as â40Â°C to +82Â°C, matching the requested range, so materials were rated for that thermal span. - Body material acetal (POM) is commonly used for fittings and performs well across that temperature range. - Sealing material is NBR (nitrile) Oâring; NBR typically has an effective temperature range roughly â40Â°C to +100Â°C (depending on compound), so â40Â°C to +82Â°C is within common NBR limits and should not inherently cause degradation. Caveats and recommendations: - Continuous operation exactly at the maximum pressure and at temperature extremes can accelerate wear; allowing a safety margin below maximum pressure is prudent for long service life. - Chemical compatibility: NBR and acetal may be affected by aggressive chemicals, solvents, or deionized water treatment chemistries.confirm compatibility with the specific fluid and any detergents or additives used. - Dynamic factors: frequent connect/disconnect cycles, pressure spikes, vibration, or contaminants can reduce seal life. - For safety-critical or long-term unattended installations, consider periodic inspection/replacement intervals and consult manufacturer datasheets or technical support for application-specific guidance. Conclusion: Functionally acceptable within the given ratings, but verify fluid compatibility and consider operational margins and maintenance to avoid premature seal wear.

Is the Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3 suitable for deionized water filtration and leak detection at 8.3 bar?

Yes. The Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3 is suitable for deionized water filtration and leak detection at 8.3 bar. The product description explicitly lists deionized water filtration and leak detection as intended uses, its working pressure is rated up to 8.3 bar, the acetal body offers good chemical resistance and mechanical strength, and sealing is provided by an NBR O-ring. Operating temperature range (-40Â°C to +82Â°C) is appropriate for typical filtration systems. Verify compatibility of NBR with any specific additives or extreme-purity requirements and ensure installation practices prevent contamination for ultrapure applications.

Does the Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3 require special maintenance for NBR o-ring longevity?

Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3 uses an NBR (nitrile rubber) O-ring. NBR is generally robust and lowâmaintenance for the stated conditions, but a few precautions will extend Oâring life and ensure reliable sealing: - Compatibility: NBR resists water, air, and many nonâaggressive fluids. Avoid prolonged contact with strong hydrocarbons, ketones, esters, concentrated acids/alkalis or chlorinated solvents, which degrade NBR. - Temperature: The operating range â40 Â°C to +82 Â°C is within typical NBR limits. Avoid sustained exposure near the upper limit (especially >80 Â°C) to prevent hardening and loss of elasticity. - Pressure and mechanical stress: The product is rated up to 8.3 bar. Ensure fittings are not repeatedly subjected to pressures beyond rating or excessive mechanical abrasion during connection/disconnection. - Chemical cleanliness: For deionized water and washing installations, maintain clean conditionsâparticulates and deposits can abrade the Oâring or compromise the seal. - Lubrication: Light, compatible lubrication (silicone or waterâbased lubricants compatible with NBR) during assembly reduces friction and wear. Avoid petroleumâbased lubricants that can swell or soften NBR. - Inspection and replacement: Periodically inspect the Oâring for cuts, flattening, cracking, or hardening. Replace if any damage or loss of elasticity is observed. For critical applications, schedule preventive replacement based on usage cycles rather than waiting for failure. - Storage: Store spare Oârings out of direct sunlight, away from ozone sources and extreme temperatures; keep in sealed packaging to avoid contamination. Following these simple practices will maximize longevity of the NBR Oâring in Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3 under the described operating conditions.

Quick connect plug with GZ NPT, with valve, acetal, PLC series DN 6,3

All products, Industrial plastic quick couplings/

Additional information

Material	P – material (plastic)

Medium-sized quick-connect plug with external NPT thread intended for washing installations, deionized water filtration, industrial machines, leak detection, etc. Length L [mm] – total length. Material: acetal. Sealing: NBR o-ring. Working pressure: up to 8.3 bar. Operating temperature: from -40°C to +82°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
CC-PLV-22-AC	PLC connector DN6.4 with 1/4" NPT thread, with valve, acetal	-	8.3	In stock	0 zł		Enquiry
CC-PLV-23-AC	PLC connector DN6.4 with GZ 3/8" NPT, with valve, acetal	-	8.3	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Medium-sized quick-connect plug with external NPT thread intended for washing installations, deionized water filtration, industrial machines, leak detection, etc. Length L [mm] – total length. Material: acetal. Sealing: NBR o-ring. Working pressure: up to 8.3 bar. Operating temperature: from -40°C to +82°C.