Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket with a shut-off valve for a diagnostic quick coupling, with an NPT female thread, used for pressure measurement in power hydraulic systems. Manufactured according to ISO 15171-1 and SAE J1502, interchangeable with couplings from other manufacturers. The hardened steel quick coupling plugs are, as standard, permanently installed in the hydraulic system, while the quick coupling sockets are connected by a hose to the pressure gauge. Connecting the socket to the plug should be done only when the system is not operating, with no pressure or very low pressure of a few bar. The socket and plug are equipped with valves that ensure leak-free connection and disconnection and tightness. Their flat surfaces minimize residual oil leakage and air inclusion into the system (leakage approx. 0.1 ml on disconnection, air inclusion approx. 0.02 ml on connection). For proper operation it is essential to keep the valve surfaces clean. Working pressure: 400 bar. Burst pressure: 1300 bar. Vacuum: up to 0.9 bar. Hydraulic oil flow at Δp = 3 bar: 4.2. Material: galvanized steel. Sealing: NBR. Operating temperature: from -40°C to +120°C.- Select options This product has multiple variants. The options may be chosen on the product page / Details90° SNAP-CHECK measuring quick coupling socket of Swedish manufacture, intended for pressure measurement in power hydraulic systems. The hardened steel quick coupling plugs are, as standard, permanently installed in the hydraulic system, while the quick coupling sockets are connected by a hose to the pressure gauge. Connecting the socket to the plug is possible under pressure up to 300 bar. The working pressure for a plug not connected to the socket is 600 bar and the minimum burst pressure is 2400 bar. The working pressure for a connected socket and plug is also 600 bar, while the minimum burst pressure is 1300 bar. The precise manufacture of the quick couplings ensures the tightness and reliability of the hydraulic system's measuring points. The range of connections for the measuring plugs allows the connection to be easily configured. The quick coupling sockets are supplied as standard with red plastic caps. Working pressure: 600 bar. Connection pressure: up to 300 bar. Body material: galvanized steel. Sealing: NBR. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSNAP-CHECK measuring quick coupling socket of Swedish manufacture, intended for pressure measurement in power hydraulic systems. The hardened steel quick coupling plugs are, as standard, permanently installed in the hydraulic system, while the quick coupling sockets are connected by a hose to the pressure gauge. Connecting the socket to the plug is possible under pressure up to 300 bar. The working pressure for a plug not connected to the socket is 600 bar and the minimum burst pressure is 2400 bar. The working pressure for a connected socket and plug is also 600 bar, while the minimum burst pressure is 1300 bar. The precise manufacture of the quick couplings ensures the tightness and reliability of the hydraulic system's measuring points. The range of connections for the measuring plugs allows the connection to be easily configured. The quick coupling sockets are supplied as standard with red plastic caps. Working pressure: 600 bar. Connection pressure: up to 300 bar. Body material: galvanized steel. Sealing: NBR. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket with a shut-off valve for a diagnostic quick coupling, with an NPT male thread, used for pressure measurement in power hydraulic systems. Manufactured according to ISO 15171-1 and SAE J1502, interchangeable with couplings from other manufacturers. The hardened steel quick coupling plugs are, as standard, permanently installed in the hydraulic system, while the quick coupling sockets are connected by a hose to the pressure gauge. Connecting the socket to the plug should be done only when the system is not operating, with no pressure or very low pressure of a few bar. The socket and plug are equipped with valves that ensure leak-free connection and disconnection and tightness. Their flat surfaces minimize residual oil leakage and air inclusion into the system (leakage approx. 0.1 ml on disconnection, air inclusion approx. 0.02 ml on connection). For proper operation it is essential to keep the valve surfaces clean. Working pressure: 400 bar. Burst pressure: 1300 bar. Vacuum: up to 0.9 bar. Hydraulic oil flow at Δp = 3 bar: 4.2. Material: galvanized steel. Sealing: NBR. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSNAP-CHECK measuring quick coupling plug of Swedish manufacture, intended for pressure measurement in power hydraulic systems. The quick coupling sockets are connected by a hose to the pressure gauge, while the hardened steel quick coupling plugs are, as standard, permanently installed in the hydraulic system and equipped with shut-off valves. Connecting the socket to the plug is possible under pressure up to 300 bar. The working pressure for a plug not connected to the socket is 600 bar and the minimum burst pressure is 2400 bar. The working pressure for a connected socket and plug is also 600 bar, while the minimum burst pressure is 1300 bar. The precise manufacture of the quick couplings ensures the tightness and reliability of the hydraulic system's measuring points. The range of connections for the measuring plugs allows the connection to be easily configured. The quick coupling plugs are supplied as standard with red plastic caps. Working pressure: 600 bar. Connection pressure: up to 300 bar. Body material: galvanized steel. Sealing: NBR. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug with a shut-off valve for a diagnostic quick coupling, with an NPT female thread, used for pressure measurement in power hydraulic systems. Manufactured according to ISO 15171-1 and SAE J1502, interchangeable with couplings from other manufacturers. The hardened steel quick coupling plugs are, as standard, permanently installed in the hydraulic system, while the quick coupling sockets remain connected by a hose to the pressure gauge. Connecting the socket to the plug should be done only when the system is not operating, with no pressure or very low pressure of a few bar. The working pressure for a plug not connected to the socket is 400 bar and the minimum burst pressure is 1600 bar. The working pressure for a connected socket and plug is also 400 bar, while the minimum burst pressure is 1300 bar. The socket and plug are equipped with valves that ensure leak-free connection and disconnection and tightness. Their flat surfaces minimize residual oil leakage and air inclusion into the system (leakage approx. 0.1 ml on disconnection, air inclusion approx. 0.02 ml on connection). For proper operation it is essential to keep the valve surfaces clean. Working pressure: 400 bar. Burst pressure: 1300 bar. Vacuum: up to 0.9 bar. Hydraulic oil flow at Δp = 3 bar: 4.2. Material: galvanized steel. Sealing: NBR. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug with a shut-off valve for a diagnostic quick coupling, with an NPT male thread, used for pressure measurement in power hydraulic systems. Manufactured according to ISO 15171-1 and SAE J1502, interchangeable with couplings from other manufacturers. The hardened steel quick coupling plugs are, as standard, permanently installed in the hydraulic system, while the quick coupling sockets remain connected by a hose to the pressure gauge. Connecting the socket to the plug should be done only when the system is not operating, with no pressure or very low pressure of a few bar. The working pressure for a plug not connected to the socket is 400 bar and the minimum burst pressure is 1600 bar. The working pressure for a connected socket and plug is also 400 bar, while the minimum burst pressure is 1300 bar. The socket and plug are equipped with valves that ensure leak-free connection and disconnection and tightness. Their flat surfaces minimize residual oil leakage and air inclusion into the system (leakage approx. 0.1 ml on disconnection, air inclusion approx. 0.02 ml on connection). For proper operation it is essential to keep the valve surfaces clean. Working pressure: 400 bar. Burst pressure: 1300 bar. Vacuum: up to 0.9 bar. Hydraulic oil flow at Δp = 3 bar: 4.2. Material: galvanized steel. Sealing: NBR. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap for a PD quick coupling plug, standard ISO 15171-1. Material: NBR.
