Is the 90Â° angle plug connector with spigot, type R46 compatible with different tubing sizes while maintaining airtight and mechanical sealing under 12 bar?

Yes . the 90Â° angle plug connector with spigot, type R46 is intended to provide reliable mechanical and airtight connections in pneumatic systems up to 12 bar while allowing quick assembly for multiple tubing changes. Key points supporting compatibility: - Sealing system: NBR sealing provides good airtight performance with common pneumatic tubing materials (e.g., PVC, PU, rubber) within the specified temperature range (-20Â°C to +60Â°C). - Working pressure: Rated to 12 bar, so when used with tubing and fittings rated for â¥12 bar, the assembly should maintain both pneumatic and mechanical sealing. - Design intent: Described as âeasy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides,â indicating the spigot and connector geometry permit repeated connections without degradation of the seal. Limitations and cautions: - Tubing size and material must match the spigot diameter and be compatible with NBR (some aggressive chemicals or very hard plastics may not seal well). - Ensure tubing is within the connectorâs specified outer/inner diameters and is installed correctly (fully pushed onto the spigot). - Operating temperature and media: avoid temperatures or media outside the stated ranges (â20Â°C to +60Â°C; vacuum, air) which can compromise NBR sealing. - For cyclic loads, vibration, or safety-critical applications, verify compatibility with supplier datasheets and perform pressure/leak tests. In summary, the 90Â° angle plug connector with spigot, type R46 is compatible with different tubing sizes and maintains airtight/mechanical sealing up to 12 bar when tubing diameter, material, installation and operating conditions conform to the connectorâs specifications.

Can the 90Â° angle plug connector with spigot, type R46 be used reliably in vacuum applications as well as compressed air up to 12 bar?

Yes. The 90Â° angle plug connector with spigot, type R46 can be used reliably in both vacuum applications and compressed air up to 12 bar. Its specifications list working medium: vacuum, air; working pressure: 12 bar; sealing: NBR; operating temperature range: -20Â°C to +60Â°C. Being designed for repeated assemblies without loss of mechanical or pneumatic sealing and made of plastic, it is suitable for vacuum and compressed-air service within those limits. Ensure compatibility of NBR with your specific contaminants and stay within the stated temperature and pressure ranges.

Does the 90Â° angle plug connector with spigot, type R46 require special installation tools to ensure long-term sealing at 12 bar?

No. The 90Â° angle plug connector with spigot, type R46 does not require special installation tools to ensure long-term sealing at 12 bar. It is designed for easy and quick repeated assemblies without loss of sealing on the mechanical and pneumatic sides. Made of plastic with NBR sealing, and rated for vacuum and air at up to 12 bar (â20Â°C to +60Â°C), the connector achieves reliable sealing through its built-in fitting and seal geometry when installed correctly. Recommended practices to ensure long-term performance: - Ensure mating components (tubes, fittings) are clean and undamaged. - Cut tubing squarely and deburr to avoid seal damage. - Push the tube fully into the spigot until it seats; follow any insertion-depth markers if present. - Avoid excessive bending or side loads at the joint; provide adequate support or strain relief. - Confirm material compatibility (NBR vs. media and temperatures). - Periodically inspect for wear, chemical attack or abrasion, especially in cyclic or high-vibration environments. If operating near temperature or chemical limits, or under unusual dynamic loads, consider additional retention/clamping or consult the supplier.

Coupling push-in angled 90° with spigot, type R46

All products, Push-in fittings/

Additional information

Material	P – material (plastic)

Coupling push-in angled 90° with spigot, type R46, Intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: plastic plastic. Working pressure: 12 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +60°C. sealing: NBR.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-2L46001	Fitting angled (elbow) RL46 hose 4 mm, spigot 4 mm, plastic	-	12	In stock	Enquiry
MW-2L46002	Fitting angled (elbow) RL46 hose 6 mm, spigot 6 mm, plastic	-	12	In stock	Enquiry
MW-2L46003	Fitting angled (elbow) RL46 hose 8 mm, spigot 8 mm, plastic	-	12	In stock	Enquiry
MW-2L46004	Fitting angled (elbow) RL46 hose 10 mm, spigot 10 mm, plastic	-	12	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Coupling push-in angled 90° with spigot, type R46, Intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: plastic plastic. Working pressure: 12 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +60°C. sealing: NBR.