Can the 90Â° twist-on end for LPG hose, brass be used with all standard LPG hose sizes and what hose inner diameter does it clamp to?

The 90Â° twist-on end for LPG hose, brass is designed as a twist-on (threaded with nut and clamping ring) tube end recommended for use with LPG hoses. It is not universally compatible with every standard LPG hose size . compatibility depends on the inner diameter (ID) of the hose and the clamping ring/nut dimensions. Typically, twist-on ends like this clamp to common LPG hose IDs (for example 6 mm, 8 mm, or 10 mm), but the exact hose inner diameter it will securely clamp to must be confirmed from the manufacturerâs specification or measured: the part will only properly seal and hold on hoses matching the endâs tube/insert diameter and the ringâs clamping range. Before use, verify the 90Â° twist-on end for LPG hose, brass is listed for the specific hose ID you have, and ensure materials and pressure ratings match LPG application requirements. If no size is given, measure the hose ID or contact the supplier for the exact clamping diameter.

Is the 90Â° twist-on end for LPG hose, brass compatible with different hose wall thicknesses and fittings?

Yes. The 90Â° twist-on end for LPG hose, brass is designed as a clamping-style tube end with a threaded nut and a compression ring, so it accommodates a range of hose wall thicknesses and standard LPG hose IDs, provided the hose OD fits under the ring and the nut can engage the hose jacket. It does not rely on a fixed internal barb, so minor variations in wall thickness are tolerated; however, for a reliable, leak-free connection you must match the fitting size to the hose ID/OD and use the correct ring and nut for that hose. Also verify compatibility with the hose material and LPG service (pressure, temperature) and follow supplier installation torque and assembly instructions.

Does the 90Â° twist-on end for LPG hose, brass require specific torque when tightening the nut and ring?

yes. use moderate, hand-tool torque only; do not overtighten. Explanation: The 90Â° twist-on end for LPG hose, brass is a mechanical clamping fitting that relies on the nut and ring compressing the hose onto the barbed/knurled tail to form a leak-free seal. Because the fitting is brass and the hose (LPG rubber) can be damaged by excessive compression, there is no single high torque value specified universally; instead follow these rules: - Tighten gradually and evenly until the fitting feels snug and the ring seats against the nut and ferrule; use hand tools (spanner) and avoid impact tools. Typical practical torque for small brass hose fittings is low. often in the range of about 5â15 Nm depending on size, but refer to the hose and fitting manufacturer for exact numbers. - Ensure the hose is fully pushed onto the barb, the ring/ferrule correctly positioned, and the nut engaged straight before final tightening. - After initial tightening, perform a pressurization and leak test (soapy water or appropriate gas leak detector) and retighten slightly if a leak is detectedânever exceed manufacturer torque. - If manufacturer instructions are unavailable, prioritize conservative torque, leak testing, and replacement of any damaged hose or ferrule rather than further tightening. Safety note: LPG fittings are safety-critical. When in doubt, use components and torque figures supplied by the hose or fitting manufacturer or have installation performed/checked by a qualified technician.

Screw-on end 90° for LPG hose, brass

All products, Thermoplastic hoses/

Additional information

Material	B – brass (bronze)

A tubular end 90°, screw-on, with a nut and ring for clamping onto the hose. Recommended for LPG hose. Material: brass.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
LE-LPG-S90-06	Okucie screw-together 90° for hose LPG 3/16", tube 6 mm, brass	-	30	In stock	0 zł		Enquiry
LE-LPG-S90-08	Okucie screw-together 90° for hose LPG 1/4", tube 8 mm, brass	-	30	In stock	0 zł		Enquiry