Is the Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C compatible with standard BSP female ports and does it require a sealant for the 60Â° cone sealing?

Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C is designed with internal BSP (British Standard Pipe) threads and a 60Â° cone sealing face. It is compatible with standard BSP female ports that use a 60Â° cone (often BSPP with conical seats or mating fittings specified for 60Â° cone sealing). For reliable sealing the 60Â° cone relies on metal-to-metal contact; therefore you should not use thread sealants (like PTFE tape or pipe dope) on the cone sealing surface itself because they can prevent proper metal seating and cause leaks. If the mating port uses a parallel thread that requires a separate thread seal for the pipe thread portion, apply sealant only to the thread portion as recommended by the system spec, avoiding contamination of the cone seat. Always follow manufacturer installation torque and surface cleanliness requirements to ensure proper 60Â° cone seal.

Does the Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C require a specific torque for proper 60Â° cone sealing?

Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C does not state a specific torque in the provided description. It uses a 60Â° cone sealing, which requires adequate tightening to achieve metal-to-metal seal without damaging threads or the cone. Proper practice is to tighten to the torque recommended by the hose/fixture manufacturer or follow BSP fitting torque tables for the size and material; if unavailable, use controlled hand-tight plus a specified number of wrench turns (typically 1â1.5 turns) or torque values from standards (e.g., ISO/BS for BSP fittings). For safety and leak-free performance, verify with supplier documentation or perform a qualified torque/pressure test rather than relying on guesswork.

Can Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C be used with stainless steel fittings without galvanic corrosion?

Noâusing Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C with stainless steel fittings carries a real risk of galvanic corrosion unless specific precautions are taken. Why: The Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C is made of carbon steel with a galvanized (zinc) coating. When carbon steel (even galvanized) is electrically coupled to stainless steel in the presence of an electrolyte (water, humid air, hydraulic fluids containing water or conductive additives), a galvanic cell can form. Zinc is more anodic and will corrode preferentially, but once zinc is depleted, the carbon steel becomes anodic relative to stainless steel and will corrode faster. Stainless steels (depending on grade) are generally more noble and can accelerate corrosion of the less noble metal. Factors that increase risk: - Presence of moisture, salts, or conductive fluids. - Dissimilar metal contact with exposed edges, threads, or damaged galvanizing. - Electrochemical potential differences between the specific stainless grade (e.g., 304, 316) and the carbon steel/zinc. - Long-term installations or cyclic wet/dry conditions. Mitigation options: - Use an insulating barrier (non-conductive sealing washers, PTFE tape alone is not sufficient electrically; use polymer or gasket isolation designed for fittings). - Ensure continuous, intact, thick zinc coating and no mechanical damage to galvanizing; recoat exposed areas. - Use a compatible stainless steel adapter instead (recommended for long-term reliability). - Use cathodic protection or sacrificial anodes in the system where feasible. - Select stainless grade with similar electrochemical behavior and minimize contact area differences. Recommendation: For hydraulic systems where moisture or conductive fluids may be present and long-term reliability is required, avoid mixing Adaptor - hydraulic coupling knee 90Â° z GW BSP, stal wÄglowa, typ A115C with stainless steel fittings. Prefer matching materials (stainless-to-stainless) or implement proper electrical isolation and protective measures.

Adaptor – hydraulic coupling knee 90° z GW BSP, stal węglowa, typ A115C

All products, High-pressure adapters/

Additional information

Material	CS – steel (cast iron)
Standard length [m]	2

90° high-pressure adapter type A115C compact with internal BSP threads (60° cone sealing). Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-A115C-02	90° Adapter GW BSP 1/8" / GW BSP 1/8"	-	400	In stock	Enquiry
TI-A115C-04	90° Adapter GW BSP 1/4" / GW BSP 1/4"	-	400	In stock	Enquiry
TI-A115C-06	90° Adapter GW BSP 3/8" / GW BSP 3/8"	-	400	In stock	Enquiry
TI-A115C-08	90° Adapter GW BSP 1/2" / GW BSP 1/2"	-	350	In stock	Enquiry
TI-A115C-12	90° Adapter GW BSP 3/4" / GW BSP 3/4"	-	315	In stock	Enquiry
TI-A115C-16	90° Adapter GW BSP 1" / GW BSP 1"	-	250	In stock	Enquiry
TI-A115C-20	90° Adapter GW BSP 1.1/4" / GW BSP 1.1/4"	-	200	In stock	Enquiry
TI-A115C-24	90° Adapter GW BSP 1.1/2" / GW BSP 1.1/2"	-	160	In stock	Enquiry
TI-A115C-32	90° Adapter GW BSP 2" / GW BSP 2"	-	125	In stock	Enquiry