Is the Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2 suitable for external machining during installation?

Yes. The Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2 is suitable for external machining during installation. The product description explicitly states "Installation - external machining" and the material AISI 316L (a corrosion-resistant stainless steel) provides the mechanical strength and machinability required for on-site external machining operations. Ensure proper tooling and follow recommended installation procedures for the specific hose type (2ST/R2A or 4SP) to maintain sealing integrity and avoid damaging the hose or sleeve.

Can the Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2 withstand external machining during installation without compromising sealing?

Yes. The Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2 is designed for installation with external machining and is manufactured from corrosionâresistant AISI 316L stainless steel. When correctly installed following manufacturer instructions and using appropriate machining practices (controlled cutting, correct tooling, avoiding overheating and surface damage), the ZF2 clamping sleeve maintains its sealing integrity. Improper machining-excessive material removal, surface scratches, burrs, or thermal damage-can compromise the seal. Conclusion: properly performed external machining during installation will not compromise sealing; poor technique can.

Can Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2 be externally machined during installation?

Yes. Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2 can be externally machined during installation. The product description explicitly states âInstallation - external machiningâ and the material AISI 316L stainless steel provides good machinability, corrosion resistance and strength suitable for final fitting adjustments. Recommendations and cautions: - Perform only light external machining (facing, trimming, minor turning) to avoid altering the clamping geometry that ensures a secure seal with 2ST (R2A) or 4SP hose assemblies. - Maintain concentricity and surface finish to preserve sealing contact and prevent stress concentrators. - Deburr and clean thoroughly after machining to remove chips and contaminants before assembly. - Follow manufacturer torque and assembly procedures for the complete fitting system; if in doubt, consult the supplier for allowable modification limits. In summary: Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2 is intended to permit external machining during installation, provided machining is limited, controlled and followed by proper cleaning and assembly.

Collet for hydraulic hoses 2ST, 4SP, AISI 316L steel, type ZF2

All products, Fittings for high-pressure hoses/

Additional information

Material	SS – stainless steel
Standard length [m]	25

ZF2 clamping sleeve for rubber hydraulic hoses type 2ST (R2A) or 4SP. Installation – external machining. Material: AISI 316L steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZF2-03-SS	Hose sleeve 2ST(R2A) 3/16", AISI 316L	5	-	In stock	Enquiry
TI-ZF2-04-SS	Sleeve for hose 2ST(R2A) and 4SP 1/4", AISI 316L	6	-	In stock	Enquiry
TI-ZF2-05-SS	Sleeve for hose 2ST(R2A) and 4SP 5/16", AISI 316L	8	-	In stock	Enquiry
TI-ZF2-06-SS	Sleeve for hose 2ST(R2A) and 4SP 3/8", AISI 316L	10	-	In stock	Enquiry
TI-ZF2-08-SS	Sleeve for hose 2ST(R2A) and 4SP 1/2", AISI 316L	12	-	In stock	Enquiry
TI-ZF2-10-SS	Sleeve for hose 2ST(R2A) and 4SP 5/8", AISI 316L	16	-	In stock	Enquiry
TI-ZF2-12-SS	Sleeve for hose 2ST(R2A) and 4SP 3/4", AISI 316L	20	-	In stock	Enquiry
TI-ZF2-16-SS	Sleeve for hose 2ST(R2A) and 4SP 1", AISI 316L	25	-	In stock	Enquiry
TI-ZF2-20-SS	Sleeve for hose 2ST(R2A) and 4SP 1.1/4", AISI 316L	32	-	In stock	Enquiry
TI-ZF2-24-SS	Sleeve for hose 2ST(R2A) and 4SP 1.1/2", AISI 316L	38	-	In stock	Enquiry
TI-ZF2-32-SS	Sleeve for hose 2ST(R2A) and 4SP 2", AISI 316L	50	-	In stock	Enquiry