Is the Connection with spigot with male thread, type R6 suitable for repeated disconnections without losing mechanical and pneumatic sealing?

Yes. Connection with spigot with male thread, type R6 is suitable for repeated disconnections without losing mechanical and pneumatic sealing. The product description explicitly states it is "easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides." Made of nickel-plated brass with NBR sealing, rated to 16 bar and for media such as vacuum and air across -20Â°C to +80Â°C, it is designed to maintain both mechanical integrity and airtight performance through repeated use. Ensure threads and sealing surfaces are kept clean and undamaged and replace NBR seals if they show wear to preserve long-term reliability.

Can Connection with spigot with male thread, type R6 be used with other sealing materials besides NBR for different temperatures or media?

Connection with spigot with male thread, type R6 is specified with NBR sealing, suitable for vacuum and air at -20Â°C to +80Â°C. Using other sealing materials is possible but must match operating temperature, chemical compatibility and pressure. For higher temperatures or aggressive media consider EPDM, FKM (Viton) or PTFE seals: EPDM for hot/wet environments and steam (but not oils), FKM for oils, fuels and higher temps (up to â200â250Â°C), PTFE for widest chemical resistance and temperature range. Verify seal dimensions fit the R6 groove, ensure retained sealing under 16 bar and pneumatic cycling, and confirm compatibility with nickelâplated brass to avoid galvanic or swelling issues. Always validate with supplier or perform pressure/compatibility tests before use.

Does Connection with spigot with male thread, type R6 require lubrication for repeated quick connects to maintain sealing?

Connection with spigot with male thread, type R6 does not typically require additional lubrication for repeated quick connects to maintain sealing, provided normal operating conditions and correct use. The coupling is designed for easy and quick multiple assemblies without loss of sealing on both mechanical and pneumatic sides. Key points: - Sealing material: NBR (nitrile rubber) is used for the seal; NBR performs well with air and vacuum and at temperatures from -20Â°C to +80Â°C. - Material and finish: nickel-plated brass construction resists wear and corrosion, supporting durable repeat connections. - Working pressure: rated to 16 bar; within this rating, the sealing geometry and NBR should maintain an effective seal over many cycles. - Lubrication: unnecessary in routine use and may attract dust or contaminants that could accelerate seal wear. However, if connections are exposed to extreme contamination, abrasive particulates, or very frequent high-cycle use beyond typical application, a light, compatible lubricant (silicone-based or specified for NBR compatibility) can reduce friction and wear. Avoid petroleum-based lubricants that can swell or degrade NBR. - Inspection and maintenance: periodically check the NBR seal for cuts, hardening, or deformation and replace if damaged. Keep mating threads and spigot surfaces clean to ensure proper sealing. - Special conditions: for temperatures near the extremes of the rated range, aggressive media, or unusually high cycle rates, consult the manufacturer for recommended lubricants and maintenance intervals. Conclusion: Under standard pneumatic use, Connection with spigot with male thread, type R6 does not require lubrication to maintain sealing; apply only clean, NBR-compatible lubricant if environmental or usage factors dictate.

Connection with spigot with a thread external, type R6

All products, Push-in fittings/

Additional information

Material	B – brass (bronze)

Connection with spigot and with a thread external, type R6, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-2006000	Fitting R6 with spigot 6 mm, M5 male	-	16	In stock	Enquiry
MW-2006001	Fitting R6 with spigot 4 mm, M5 male	-	16	In stock	Enquiry
MW-2006002	Fitting R6 with spigot 4 mm, 1/8" BSP male	-	16	In stock	Enquiry
MW-2006003	Fitting R6 with spigot 4 mm, 1/4" BSP male	-	16	In stock	Enquiry
MW-2006004	Fitting R6 with spigot 5 mm, M5 male	-	16	In stock	Enquiry
MW-2006005	Fitting R6 with spigot 5 mm, 1/8" BSP male	-	16	In stock	Enquiry
MW-2006006	Fitting R6 with spigot 5 mm, 1/4" BSP male	-	16	In stock	Enquiry
MW-2006007	Fitting R6 with spigot 6 mm, 1/8" BSP male	-	16	In stock	Enquiry
MW-2006008	Fitting R6 with spigot 6 mm, 1/4" BSP male	-	16	In stock	Enquiry
MW-2006009	Fitting R6 with spigot 8 mm, 1/8" BSP male	-	16	In stock	Enquiry
MW-2006010	Fitting R6 with spigot 8 mm, 1/4" BSP male	-	16	In stock	Enquiry
MW-2006011	Fitting R6 with spigot 8 mm, 3/8" BSP male	-	16	In stock	Enquiry
MW-2006012	Fitting R6 with spigot 10 mm, 1/4" BSP male	-	16	In stock	Enquiry
MW-2006013	Fitting R6 with spigot 10 mm, 3/8" BSP male	-	16	In stock	Enquiry
MW-2006014	Fitting R6 with spigot 12 mm, 3/8" BSP male	-	16	In stock	Enquiry
MW-2006015	Fitting R6 with spigot 12 mm, 1/2" BSP male	-	16	In stock	Enquiry
MW-2006016	Fitting R6 with spigot 14 mm, 3/8" BSP male	-	16	In stock	Enquiry
MW-2006017	Fitting R6 with spigot 14 mm, 1/2" BSP male	-	16	In stock	Enquiry
MW-2006019	Fitting R6 with spigot 12 mm, 1/4" BSP male	-	16	In stock	Enquiry
MW-2006020	Fitting R6 with spigot 4 mm, M7 male	-	16	In stock	Enquiry
MW-2006021	Fitting R6 with spigot 6 mm, M7 male	-	16	In stock	Enquiry
MW-2006022	Fitting R6 with spigot 10 mm, 1/2" BSP male	-	16	In stock	Enquiry
MW-2006101	Fitting R6 with spigot 6 mm, M12x1.5 male	-	16	In stock	Enquiry
MW-2006102	Fitting R6 with spigot 8 mm, M12x1.5 male	-	16	In stock	Enquiry
MW-2006A01	Fitting R6 with spigot 3.17 mm, M5 male	-	16	In stock	Enquiry
MW-2006A02	Fitting R6 with spigot 3 mm, M5 male	-	16	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Connection with spigot and with a thread external, type R6, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.