Can I use the IBC tee with GZ BSP/2xGW BSP, polypropylene with LDPE gasket at 7 bar and temperatures up to +80Â°C temporarily?

Yes . the IBC tee with GZ BSP/2xGW BSP, polypropylene with LDPE gasket can be used at 7 bar and temperatures up to +80Â°C only temporarily. The productâs specified working pressure is up to 7 bar and its normal operating temperature range is â10Â°C to +70Â°C, with a clear allowance for temporary exposure up to +80Â°C. That means continuous use should be limited to â¤+70Â°C; short-term excursions to +80Â°C are acceptable per the manufacturerâs limits. Monitor for any signs of stress, deformation or gasket failure after thermal cycling, and avoid sustained operation at the +80Â°C level to prevent accelerated material aging or loss of seal integrity.

Can the IBC tee with GZ BSP/2xGW BSP, polypropylene and LDPE gasket be used continuously at 7 bar and up to +70Â°C?

Yes. The IBC tee with GZ BSP/2xGW BSP, polypropylene with an LDPE gasket is rated for working pressure up to 7 bar and an operating temperature range of â10Â°C to +70Â°C (temporary up to +80Â°C). Therefore it can be used continuously at 7 bar and up to +70Â°C provided installation and service conditions match the stated ratings and the media are compatible with polypropylene and LDPE. Do not exceed continuous exposure limits or use with aggressive chemicals that may degrade the materials.

Is the IBC tee with GZ BSP/2xGW BSP, polypropylene and LDPE gasket safe for chemical use at 7 bar?

Possibly, but not guaranteed. you need confirm chemical compatibility and application details before use at 7 bar. Explanation and key checks: - The IBC tee with GZ BSP/2xGW BSP, polypropylene with LDPE gasket is rated for working pressure up to 7 bar and temperatures â10Â°C to +70Â°C (short-term +80Â°C). Mechanically, that means the fitting is designed to withstand 7 bar under the specified temperature range. - Chemical safety depends on the stored/transported chemical. Polypropylene (PP) and low-density polyethylene (LDPE) have good resistance to many acids, alkalis and organic solvents, but they are attacked by some aggressive solvents (strong chlorinated hydrocarbons, aromatic hydrocarbons, concentrated oxidizers like nitric acid at elevated temperature), certain amines, and some hydrocarbons. LDPE gaskets can swell, soften or degrade with some solvents and fuels. - Factors that affect suitability: chemical identity and concentration, temperature (higher temperatures accelerate degradation), exposure time, presence of solvents or oxidizers, pressure cycling, mechanical stresses, and compatibility of thread seals/assembly materials. Recommended steps before use at 7 bar: 1. Identify the exact chemical, concentration and operating temperature. 2. Check a reputable chemical compatibility chart for PP and LDPE for that specific chemical and conditions. 3. Confirm the gasket material (LDPE) compatibility; if incompatible, replace with a suitable gasket (e.g., EPDM, FKM, PTFE) rated for the chemical and 7 bar. 4. Verify sealing method and assembly torque to ensure leak-free performance at pressure. 5. Consider pressure testing in situ and review applicable standards/regulations for IBC fittings in your jurisdiction. 6. If in doubt or handling hazardous chemicals, consult the fitting manufacturer or a materials engineer. Conclusion: The IBC tee with GZ BSP/2xGW BSP, polypropylene is mechanically rated for 7 bar, but safe chemical use at 7 bar depends on confirmed compatibility of polypropylene and the LDPE gasket with your specific chemical, concentration and temperature.

Tee IBC with male thread BSP/2x female thread BSP, polypropylene

Additional information

Material	P – material (plastic)

Tee IBC with a thread external BSP, equipped in a gasket and 2x a thread internal BSP. Material: polypropylene. gasket: low-density polyethylene (LDPE). Working pressure: up to 7 bar. Operating temperature: from -10°C to +70°C (momentarily up to +80°C).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
AC-IBM200-2F200	Tee IBC with 2" BSP male / 2 x 2" BSP female	-	7	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Tee IBC with a thread external BSP, equipped in a gasket and 2x a thread internal BSP. Material: polypropylene. gasket: low-density polyethylene (LDPE). Working pressure: up to 7 bar. Operating temperature: from -10°C to +70°C (momentarily up to +80°C).