Is the Screw for BANJO inch, carbon steel compatible with standard inch fittings and safe to use without a washer?

Screw for BANJO inch, carbon steel . compatibility and washer safety Based on the provided description (Banjo type - Z, inch screw without washer; material: carbon steel, galvanized): 1. Compatibility with standard inch fittings: - If your system uses Banjo fittings specified for the same inch size and Banjo type Z, the Screw for BANJO inch, carbon steel should be physically compatible. "Inch" sizing implies it matches inch-standard banjo bolt threads and dimensions. Always confirm the exact thread pitch and banjo flange dimensions against the mating fitting before installation. 2. Safety and use without a washer: - The product is explicitly described as "inch screw without washer." Using it without a washer may be acceptable only if the mating banjo fitting or assembly includes an integrated sealing surface or a gasket (e.g., copper crush washer or O-ring) elsewhere in the joint. Typically, banjo fittings require a soft crush washer (copper/aluminum) or a compatible sealing element on both sides of the banjo eye to ensure leak-free hydraulic or fluid connections. - Using a plain steel banjo screw alone (even galvanized carbon steel) without a proper washer or seal risks fluid leakage and potential failure under pressure. Galvanization provides corrosion resistance but does not provide sealing. Recommendation: Verify thread pitch and dimensions for fit, and do not omit a proper sealing washer/gasket unless the specific application or mating part design explicitly provides an alternative sealing method.

Can the Screw for BANJO inch, carbon steel be used in high-pressure systems without a washer?

No. Screw for BANJO inch, carbon steel (Banjo type - Z, inch screw without washer) is not suitable for high-pressure systems without a washer. Banjo fittings rely on a sealing surface and typically require a crush or copper washer (or properly rated gasket) to prevent leaks under pressure. The described product is an inch screw without washer and, although made of carbon steel and galvanized, lacks the necessary sealing element and likely the pressure-rated sealing face. Using it without a washer risks leakage, thread damage, and potential system failure. Always use the correct banjo bolt plus specified washer/gasket rated for your system pressure or consult the manufacturer/specifications before installation.

Does the Screw for BANJO inch, carbon steel require a specific torque when used without a washer?

Screw for BANJO inch, carbon steel used without a washer does not have a universally specified torque in the provided description (Banjo type - Z, inch screw without washer. Material: carbon steel, galvanized). Absence of a washer changes load distribution and sealing behavior, so recommended torque depends on application factors not given: bolt size (inch), thread pitch, material strength, mating material, flange geometry of the banjo fitting, presence of sealant or Oâring, and operating pressure/temperature. General guidance: - Reduce torque compared with values for bolted joints with a washer to avoid crushing, galling or thread stripping because the head bears directly on the banjo surface. - Use standard torque tables for carbon steel bolts of the specific inch size as a starting point, then apply a reduction (commonly 10â25%) when no washer is used, and further adjust for galvanizing (which can increase friction). - If sealing a hydraulic/fluid joint, follow manufacturer torque or use a torque that ensures proper gasket/seat compression without overstressing the banjo. If none provided, use a controlled trial: tighten to incremental torques and inspect for deformation, leaks, and thread condition. For critical or safetyârelated systems, obtain manufacturer torque specification for Screw for BANJO inch, carbon steel or consult an engineer. If possible, add the correct washer, spacer, or specified sealing element to allow use of standard torque values.

Bolt for BANJO calowa, carbon steel

All products, Fittings for high-pressure hoses/

Additional information

Bolt without washers for fitting BANJO type – Z, calowa. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZBB610-02	Bolt for BANJO 1/8"	-	-	In stock	Enquiry
TI-ZBB610-04	Bolt for BANJO 1/4"	-	-	In stock	Enquiry
TI-ZBB610-06	Bolt for BANJO 3/8"	-	-	In stock	Enquiry
TI-ZBB610-08	Bolt for BANJO 1/2"	-	-	In stock	Enquiry
TI-ZBB610-10	Bolt for BANJO 5/8"	-	-	In stock	Enquiry
TI-ZBB610-12	Bolt for BANJO 3/4"	-	-	In stock	Enquiry
TI-ZBB610-16	Bolt for BANJO 1"	-	-	In stock	Enquiry