Can LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH be used with chemicals other than water and which gasket material is recommended?

Can LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH be used with chemicals other than water and which gasket material is recommended? Yes . LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH can be used with media other than water, but compatibility depends on the chemical aggressiveness and temperature of the medium. The connectorâs body is carbon steel (galvanized), max working pressure 12.5 bar (liquids) and 8 bar (air), vacuum-capable, operating temperature â50Â°C to +120Â°C. The standard sealing is EPDM, which is suitable for many aqueous media, water-based chemicals, and some dilute acids/alkalis, but is not recommended for hydrocarbons, oils, strong solvents, ketones, or many aggressive chemicals. When selecting for chemicals other than water, choose gasket material based on chemical compatibility and operating temperature: - EPDM (standard): good for hot/cold water, steam (limited), glycols, many detergents, dilute acids/alkalis; poor for oils, fuels, hydrocarbons, aromatic solvents. Temperature range fits the connector. - If service involves oils, fuels, hydrocarbons, or many solvents -> use NBR (nitrile) or FKM/Viton depending on temperature and chemical concentration (FKM for higher chemical resistance and temperature). - For highly aggressive chemicals, strong oxidizers, or specialty solvents -> consider PTFE (Teflon) or other specialty elastomers; verify compatibility case-by-case. Always verify chemical compatibility charts for the chosen gasket material with the specific chemical, concentration and temperature. If in doubt, consult the manufacturer or a materials specialist before use.

Is LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH suitable for use with oils or fuels and which gasket material should be chosen?

LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH is primarily specified for water and bulk materials; it can be used with oils or fuels only if a compatible gasket is fitted. Standard gasket is EPDM, which is not suitable for most oils and fuels. For oils/fuels choose a gasket resistant to hydrocarbons (e.g., NBR/Nitrile or FKM/Viton depending on fuel type and temperature). Verify chemical compatibility with the specific oil/fuel and operating temperature range (-50Â°C to +120Â°C). Also confirm fuel-grade suitability of galvanised carbon steel and expected pressure (max 12.5 bar liquids). If in doubt, consult manufacturer for recommended gasket material and certification for fuels.

Can LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH be used with abrasive bulk materials like cement or minerals?

Yes. LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH can be used with abrasive bulk materials like cement or minerals, but with conditions. Why it can work: - The product description explicitly lists transport and unloading of bulk materials (including cement and minerals) among typical applications. - Construction in galvanized carbon steel gives mechanical strength suitable for handling solid bulk flows. - Designed for pressure/vacuum duty and wide temperature range (â50Â°C to +120Â°C), which fits many industrial handling scenarios. - Standard EPDM gasket provides good general sealing and vacuum tightness. Important considerations and limitations: - Abrasive wear: repeated flow of abrasive solids (cement, minerals) will accelerate wear on internal surfaces, sealing faces and the lever/valve seating. For high-frequency or heavy-duty use, inspect and maintain regularly or consider more abrasion-resistant materials/coatings. - Gasket compatibility: the standard EPDM gasket is suitable for many uses but may be compromised by specific mineral additives, oils, or chemicals present in the bulk. Check chemical compatibility and, if needed, select a different gasket material. - Pressure limits: observe maximum working pressures (12.5 bar for liquids, 8 bar for air). Dynamic loads from pneumatic conveying or dense bulk slurries must stay within these limits. - Installation practice: ensure correct alignment, support and protection from ingress of abrasive dust to prolong life; schedule inspections and gasket replacements. Conclusion: For general transport and unloading of cement or minerals, LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH is suitable when used within its pressure/temperature ratings, with appropriate gasket selection and proactive maintenance to manage abrasion.

LAUX 42 lever connector tee plug-socket / socket, carbon steel, KTH

All products, Lever couplings/

Additional information

Material	CS – steel (cast iron)

LAUX 42 lever connector tee plug-socket / socket with wide applications, e.g.: for the transport and unloading of bulk materials (grains, flours, feeds, granules, cement, minerals), for pressure and vacuum pumps, for the construction of temporary water and air installations in construction, mining, agriculture, for irrigation systems. When selecting a connector for a medium other than water, attention should be paid to the correct selection of gasket material. The standard sealing is an EPDM gasket. Material: carbon steel, galvanized. Maximum working pressure: 12.5 bar (for liquids), 8 bar (for air). Tightness under vacuum. Operating temperature: from -50°C to +120°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TF-KTH-048-048	KTH tee plug-socket 48 mm / socket 48 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-076-048	KTH tee plug-socket 76 mm / socket 48 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-076-076	KTH tee plug-socket 76 mm / socket 76 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-102-048	KTH tee plug-socket 102 mm / socket 48 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-102-076	KTH tee plug-socket 102 mm / socket 76 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-102-102	KTH tee plug-socket 102 mm / socket 102 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-133-076	KTH tee plug-socket 133 mm / socket 76 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-133-102	KTH tee plug-socket 133 mm / socket 102 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-133-133	KTH tee plug-socket 133 mm / socket 133 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-152-102	KTH tee plug-socket 152 mm / socket 102 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-152-133	KTH tee plug-socket 152 mm / socket 133 mm, galvanized steel.	-	12.5	In stock	Enquiry
TF-KTH-152-152	KTH tee plug-socket 152 mm / socket 152 mm, galvanized steel.	-	12.5	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

LAUX 42 lever connector tee plug-socket / socket with wide applications, e.g.: for the transport and unloading of bulk materials (grains, flours, feeds, granules, cement, minerals), for pressure and vacuum pumps, for the construction of temporary water and air installations in construction, mining, agriculture, for irrigation systems. When selecting a connector for a medium other than water, attention should be paid to the correct selection of gasket material. The standard sealing is an EPDM gasket. Material: carbon steel, galvanized. Maximum working pressure: 12.5 bar (for liquids), 8 bar (for air). Tightness under vacuum. Operating temperature: from -50°C to +120°C.