Can Collets type LDR, LD, LR, carbon steel fit hoses if I only know the hose internal diameter Dw and external diameter Dz?

Yes . Collets type LDR, LD, LR, carbon steel can be selected using only the hose internal diameter (Dw) and external diameter (Dz), because the sleeve selection is based on those two dimensions. How to choose: - Use Dw to check compatibility with the sleeve internal diameter D2. - Use Dz to check compatibility with the sleeve external diameter D1 and the locking diameter D3 where applicable. - Ensure the sleeve length L is equal to or slightly (a few mm) greater than the tail length Lk of the chosen end fitting. - Select type by end fitting: LD for corrugated-tail ends (NH-xxK-xxx), LR for ends intended for shell clamps (TW-KRS-xxx, NH-xxR-xxx), LDR when you need compatibility with both end types. - Note material: galvanized carbon steel . verify suitability for your application (corrosion, hygiene requirements). If you provide Dw and Dz (and optionally required end type and Lk), I can recommend specific D1/D2/D3 values and whether LDR/LD/LR is appropriate.

Do Collets type LDR, LD, LR, carbon steel require knowing both hose internal diameter Dw and external diameter Dz to select the correct sleeve?

Yes. For Collets type LDR, LD, LR, carbon steel you must know both the hose internal diameter (Dw / D2) and external diameter (Dz / D1) to select the correct sleeve. Selection depends on matching D2 to the hose bore and D1 to the hose outer size so the sleeve fits the tail and locks at the specified locking diameter D3. Also check sleeve length L versus tail length Lk (L may be a few mm longer). LDR fits both tail types, LD for corrugated tails, LR for shell-clamp tails.

Do Collets type LDR, LD, LR, carbon steel require both hose inner diameter Dw and outer diameter Dz to choose the correct sleeve?

Yes. to choose the correct sleeve for Collets type LDR, LD, LR, carbon steel you must consider both the hose inner diameter (Dw) and outer diameter (Dz). These sleeves are designed to clamp specific hygienic stainless steel ends (NH-xxK-xxx) and ends for shell clamps (e.g., TW-KRS-xxx, NH-xxR-xxx) used on industrial hoses. Selection uses: - Dw (internal diameter) to ensure the sleeve fits over the hose inner profile and mates correctly with the endâs tail. - Dz (external diameter) to match the sleeveâs internal diameter (D2) and the sleeveâs external diameter (D1), and to ensure proper locking diameter (D3) when clamped. Notes: - LR sleeves: only for ends under shell clamp. - LD sleeves: only for ends with corrugated tail. - LDR sleeves: for both types. - Sleeve length L should be slightly (a few mm) greater than the end tail length Lk. - Material: galvanized carbon steel. Therefore both Dw and Dz are required to select the correct sleeve dimensions (D1, D2, D3) for secure clamping.

Ferrules type LDR, LD, LR, carbon steel

Additional information

Material	CS – steel (cast iron)

Type LDR, LD, LR ferrules are intended for crimping hygienic stainless steel fittings (with a serrated tail) type NH-xxK-xxx and fittings with a hose tail for an RS shell clamp, e.g., TW-KRS-xxx, NH-xxR-xxx, onto industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral – suction and delivery hoses). The ferrule should be selected taking into account the inner diameter Dw and outer diameter Dz of the hose. The ferrule length L may be slightly (a few mm) greater than the length of the fitting tail Lk. LR ferrules – only for fittings for a shell clamp, LD – only for fittings with a serrated tail, LDR – ferrules for both fitting types. Diameter D1 – outer diameter. Diameter D2 – inner diameter. Diameter D3 – lock diameter. Material: galvanized carbon steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-LDR-045-20	Ferrule type LDR 45 mm for hose 1.1/4"	32	-	In stock	Enquiry
TI-LDR-048-20	Ferrule type LDR 48 mm for hose 1.1/4"	32	-	In stock	Enquiry
TI-LDR-050-24	Ferrule type LDR 50 mm for hose 1.1/2"	38	-	In stock	Enquiry
TI-LDR-056-24	Ferrule type LDR 56 mm for hose 1.1/2"	38	-	In stock	Enquiry
TI-LDR-064-32	Ferrule type LDR 64 mm for hose 2"	50	-	In stock	Enquiry
TI-LDR-068-32	Ferrule type LDR 68 mm for hose 2"	50	-	In stock	Enquiry
TI-LDR-071-32	Ferrule type LDR 71 mm for hose 2"	50	-	In stock	Enquiry
TI-LDR-073-32	Ferrule type LDR 73 mm for hose 2"	50	-	In stock	Enquiry
TI-LDR-078-40	Ferrule type LDR 78 mm for hose 2.1/2"	65	-	In stock	Enquiry
TI-LDR-082-40	Ferrule type LDR 82 mm for hose 2.1/2"	65	-	In stock	Enquiry
TI-LDR-085-40	Ferrule type LDR 85 mm for hose 2.1/2"	65	-	In stock	Enquiry
TI-LDR-090-48	Ferrule type LDR 90 mm for hose 3"	80	-	In stock	Enquiry
TI-LDR-092-40	Ferrule type LDR 92 mm for hose 2.1/2"	65	-	In stock	Enquiry
TI-LDR-092-48	Ferrule type LDR 92 mm for hose 3"	80	-	In stock	Enquiry
TI-LDR-095-48	Ferrule type LDR 95 mm for hose 3"	80	-	In stock	Enquiry
TI-LDR-098-48	Ferrule type LDR 98 mm for hose 3"	80	-	In stock	Enquiry
TI-LDR-114-48	Ferrule type LDR 114 mm for hose 3"	80	-	In stock	Enquiry
TI-LR-115-64	Ferrule type LR 115 mm for hose 4"	100	-	In stock	Enquiry
TI-LR-120-64	Ferrule type LR 120 mm for hose 4"	100	-	In stock	Enquiry
TI-LR-123-64	Ferrule type LR 123 mm for hose 4"	100	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Type LDR, LD, LR ferrules are intended for crimping hygienic stainless steel fittings (with a serrated tail) type NH-xxK-xxx and fittings with a hose tail for an RS shell clamp, e.g., TW-KRS-xxx, NH-xxR-xxx, onto industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral – suction and delivery hoses). The ferrule should be selected taking into account the inner diameter Dw and outer diameter Dz of the hose. The ferrule length L may be slightly (a few mm) greater than the length of the fitting tail Lk. LR ferrules – only for fittings for a shell clamp, LD – only for fittings with a serrated tail, LDR – ferrules for both fitting types. Diameter D1 – outer diameter. Diameter D2 – inner diameter. Diameter D3 – lock diameter. Material: galvanized carbon steel.