Can the Nut for twisted couplings for pneumatic hoses C series, type C10 be used with soft-plastic hoses and nickel-plated brass fittings without causing damage when tightened?

Yes. Nut for twisted couplings for pneumatic hoses C series, type C10 Format is intended for joining hoses made of soft plastics: the hose fits over the coupling end and is secured by screwing the nut. Made of nickelâplated brass, the nut provides a firm mechanical clamp without cutting or crushing the softâplastic hose when properly installed. To avoid damage, ensure the hose is the correct inner diameter for the coupling, push it fully onto the fitting, and tighten the nut only to the recommended torque or until it seats securely.avoid excessive force. Also verify compatibility of the specific softâplastic compound with nickelâplated brass to prevent chemical degradation over time. When these conditions are met, Nut for twisted couplings for pneumatic hoses C series, type C10 Format can be used safely with softâplastic hoses and nickelâplated brass fittings.

Will the Nut for twisted couplings for pneumatic hoses C series, type C10 securely seal soft-plastic hoses on nickel-plated brass fittings without leaks?

Yes - Nut for twisted couplings for pneumatic hoses C series, type C10 should securely seal soft-plastic hoses on nickel-plated brass fittings when used as intended. The design joins hoses by sliding the soft-plastic hose over the fitting end and tightening the nut, which compresses and holds the hose in place. Nickel-plated brass provides a smooth, durable mating surface that helps prevent damage to soft hose material and reduces corrosion that could cause leaks. Proper sealing depends on correct hose size, full insertion onto the fitting, and adequately tightened nut (avoiding under- or overtightening). For best results, verify compatibility of hose inner diameter with the C10 fitting and inspect for wear or cuts; consider an appropriate clamp or sealant if operating at higher pressures or with aggressive media.

Nut for twisted couplings for pneumatic hoses C series, type C10

Q: Does the Nut for twisted couplings for pneumatic hoses C series, type C10 require a ferrule when used with soft-plastic hoses?

Does the Nut for twisted couplings for pneumatic hoses C series, type C10 require a ferrule when used with soft-plastic hoses? Based on the product descriptionâNut for socket couplings designed for joining hoses made of soft plastics; the connection occurs by fitting the hose onto the end and tightening it by screwing the nut; material: nickel-plated brassâthe Nut for twisted couplings for pneumatic hoses C series, type C10 does not require a separate ferrule when used with soft-plastic hoses. The design relies on the hose being pushed over the fitting end and retained by the tightening action of the nut, providing a secure seal without an additional ferrule.

All products, Tubular fittings/

Additional information

Nut for socket couplings designed for joining hoses made of soft plastics. The connection occurs by fitting the hose onto the end and tightening it by screwing the nut. Material: nickel-plated brass.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-2310001	Nut C10, hose 4/2, G1/2 M7x0.5	-	-	In stock	Enquiry
MW-2310002	Nut C10, hose 6/4 - M5, thread M8x0.5	-	-	In stock	Enquiry
MW-2310003	Nut C10, hose 6/4, G1/2 M10x1	-	-	In stock	Enquiry
MW-2310004	Nut C10, hose 8/6, G1/2 M12x1	-	-	In stock	Enquiry
MW-2310005	Nut C10, hose 10/8, G1/2 M14x1	-	-	In stock	Enquiry
MW-2310006	Nut C10, hose 12/10, G thread M16x1	-	-	In stock	Enquiry
MW-2310009	Nut C10, hose 5/3, G7/0.75	-	-	In stock	Enquiry
MW-2310010	Nut C10, hose 6/4, G-thread M8x0.75	-	-	In stock	Enquiry
MW-2310011	Nut C10, hose 15/12.5, G thread M20x1	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Nut for socket couplings designed for joining hoses made of soft plastics. The connection occurs by fitting the hose onto the end and tightening it by screwing the nut. Material: nickel-plated brass.