Is the Stainless steel ball valve with BSP thread, type 2013N suitable for use with steam at 200Â°C and does it comply with PED 2014/68/EU?

Stainless steel ball valve with BSP thread, type 2013N . based on the provided description . is suitable for use with steam at 200Â°C and complies with PED 2014/68/EU, with the following caveats: - Temperature compatibility: The valveâs stated operating temperature range is -20Â°C to +200Â°C, so 200Â°C is at the upper limit. Materials: CF8M (stainless steel) body and ball are suitable for steam at that temperature; however the sealing materials are PTFE/RTFE for ball sealing and PTFE for stem sealing. PTFE can be used near 200Â°C but long-term exposure at the maximum temperature may reduce seal life and mechanical properties. For reliable long-term steam service at 200Â°C, verify seal temperature rating, consider reduced service life, and evaluate whether high-temperature-grade PTFE or alternative seals are required. - PED compliance: The description explicitly states it meets the requirements of the PED directive 2014/68/EU. Ensure the specific valve variant has the necessary documentation (e.g., Declaration of Conformity, applicable category/module, and CE marking) for your pressure/fluids and installation. Recommendation: Proceed with use at 200Â°C only after confirming seal material certification for continuous steam at that temperature and obtaining the manufacturerâs PED documentation and any required pressure/temperature rating tables for your operating conditions.

Can the Stainless steel ball valve with BSP thread, type 2013N be used for aggressive chemicals considering PTFE seals and CF8M construction?

Stainless steel ball valve with BSP thread, type 2013N can be used with many aggressive chemicals, but suitability depends on the specific media and conditions. Its CF8M (AISI 316) body and ball offer good corrosion resistance; PTFE/RTFE seals and PTFE stem packing provide excellent chemical compatibility and wide resistance range. Operating temperature -20Â°C to +200Â°C is acceptable for most PTFE applications. Before use with aggressive or highly oxidizing agents, fluorinated solvents, molten alkali metals, or halogenated hydrocarbons at high temperature/pressure, verify chemical compatibility of CF8M and PTFE with the specific chemical, concentration, temperature and pressure. Also confirm compliance with PED 2014/68/EU for your application. If in doubt, consult manufacturer or materials-compatibility charts.

Can the Stainless steel ball valve with BSP thread, type 2013N be used for high-pressure compressed air applications?

Yes. the Stainless steel ball valve with BSP thread, type 2013N can be used for high-pressure compressed air applications with conditions noted below. Why it is suitable - Designed for industrial installations and approved under PED 2014/68/EU, indicating suitability for pressure equipment in many industrial compressed-air systems. - Materials (body and ball: stainless steel CF8M; lever: AISI 304) provide good mechanical strength and corrosion resistance for air and gases. - Seals (PTFE/RTFE on the ball and PTFE stem sealing) are compatible with compressed air across a wide temperature range (-20Â°C to +200Â°C). Considerations and limits - âHigh-pressureâ must be defined: the exact maximum allowable working pressure (MAWP) is not specified in the provided description. Verify the valveâs rated pressure (PN/bar or psi) from the manufacturerâs datasheet or certification to ensure it meets your system pressure. - Check thread and installation integrity: BSP thread connections must be properly sealed and torqued; for very high pressures, consider thread type, use of appropriate fittings, and possible use of additional reinforcement (e.g., flanged or welded connections) if recommended. - Temperature and seal compatibility: PTFE seals perform well up to +200Â°C but confirm compatibility with any contaminants (oil, lubricants, condensates) present in your compressed-air system. - Safety and standards: Ensure installation complies with applicable standards, safety margins, and periodic inspection requirements for high-pressure compressed-air systems. Recommendation Confirm the valveâs specific pressure rating and any installation instructions with the manufacturer or datasheet before using Stainless steel ball valve with BSP thread, type 2013N in your high-pressure compressed air application.

Stainless steel ball valve with BSP thread, type 2013N

All products, Ball valves/

Additional information

Material	SS – stainless steel

Universal three-piece ball valve with full bore and lever lock type 2013N, intended for industrial installations. It can be used for air, gases, water, steam, chemicals, petrochemical products, etc., considering the chemical resistance of the valve material and sealing. It meets the requirements of the PED directive 2014/68/EU. Body material: stainless steel CF8M. Ball material: stainless steel CF8M. Lever material: steel AISI 304. Ball sealing: PTFE / RTFE. Stem sealing: PTFE. Connection: BSP thread. Operating temperature: from -20°C to +200°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HT-2013N-08	Ball valve type 2013N G 1/4" BSP, AISI 316	-	63	In stock	Enquiry
HT-2013N-08X	Ball valve type 2013N-X BSP 1/4", AISI 316	-	63	In stock	Enquiry
HT-2013N-10	Ball valve type 2013N G 3/8" BSP, AISI 316	-	63	In stock	Enquiry
HT-2013N-10X	Ball valve type 2013N-X BSP 3/8", AISI 316	-	63	In stock	Enquiry
HT-2013N-15	Ball valve type 2013N G 1/2" BSP, AISI 316	-	63	In stock	Enquiry
HT-2013N-15X	Ball valve type 2013N-X BSP 1/2", AISI 316	-	63	In stock	Enquiry
HT-2013N-20	Ball valve type 2013N G 3/4" BSP, AISI 316	-	63	In stock	Enquiry
HT-2013N-20X	Ball valve type 2013N-X GW BSP 3/4", AISI 316	-	63	In stock	Enquiry
HT-2013N-25	Ball valve type 2013N G 1" BSP, AISI 316	-	63	In stock	Enquiry
HT-2013N-25X	Ball valve type 2013N-X BSP 1", AISI 316	-	63	In stock	Enquiry
HT-2013N-32	Ball valve type 2013N GW BSP 1.1/4", AISI 316	-	63	In stock	Enquiry
HT-2013N-32X	Ball valve type 2013N-X GW BSP 1.1/4", AISI 316	-	63	In stock	Enquiry
HT-2013N-40	Ball valve type 2013N G 1.1/2", AISI 316	-	63	In stock	Enquiry
HT-2013N-40X	Ball valve type 2013N-X GW BSP 1.1/2", AISI 316	-	63	In stock	Enquiry
HT-2013N-50	Ball valve type 2013N G 2" BSP, AISI 316	-	63	In stock	Enquiry
HT-2013N-50X	Ball valve type 2013N-X BSP 2", AISI 316	-	63	In stock	Enquiry
HT-2013N-65	Ball valve type 2013N GW BSP 2.1/2", AISI 316	-	63	In stock	Enquiry
HT-2013N-65X	Ball valve type 2013N-X BSP 2.1/2", AISI 316	-	63	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Universal three-piece ball valve with full bore and lever lock type 2013N, intended for industrial installations. It can be used for air, gases, water, steam, chemicals, petrochemical products, etc., considering the chemical resistance of the valve material and sealing. It meets the requirements of the PED directive 2014/68/EU. Body material: stainless steel CF8M. Ball material: stainless steel CF8M. Lever material: steel AISI 304. Ball sealing: PTFE / RTFE. Stem sealing: PTFE. Connection: BSP thread. Operating temperature: from -20°C to +200°C.