Is the Set of standard jaws for FINN-POWER P20 press brake compatible with surface-hardened steel tooling and what maintenance is required?

Yes. The Set of standard jaws for FINN-POWER P20 press brake is made of surface-hardened steel, so it is compatible with surface-hardened steel tooling. Compatibility notes and maintenance: - Wear resistance: Surface hardening provides good wear resistance for typical bending and crimping operations; avoid applications with excessive abrasion or impacts that exceed the jaw hardness. - Matching hardness: Use tooling with compatible hardness to prevent premature wear or galling.do not mate very soft tooling against much harder jaws without appropriate protection. - Cleaning: Keep mating surfaces free of debris, swarf and bending lubricant residues after each shift to prevent surface damage. - Inspection: Regularly inspect for chips, cracks, flatness and loss of hardness; check clamping faces and locating features before each job change. - Lubrication: Lightly oil moving/clamping interfaces and non-working surfaces to prevent corrosion; do not apply grease to working faces that contact the workpiece where it could contaminate parts. - Fastening: Ensure screws/bolts are torqued to manufacturer specifications and check hardware periodically. - Reconditioning: Minor wear can be restored by resurfacing or rehardening by a qualified service provider; replace jaws if hardness, geometry or safety is compromised. - Storage: Store in a dry, protected environment; use protective caps or covers for finished faces. Following these practices will maintain performance and longevity of the Set of standard jaws for FINN-POWER P20 press brake when used with surface-hardened steel tooling.

Can the Set of standard jaws for FINN-POWER P20 press brake be used for high-volume bending of surface-hardened steel without additional tooling modifications?

No. The Set of standard jaws for FINN-POWER P20 press brake Format is not suitable for high-volume bending of surface-hardened steel without additional tooling modifications. Surface-hardened steel requires tooling with increased wear resistance, specific radii, and often special coatings or hardened inserts to prevent rapid wear, chipping, and loss of dimensional accuracy. For high-volume production you should use hardened, wear-resistant tooling or retrofit the standard jaws with suitable hardened/ coated elements and verify punch/die geometry for the material hardness to ensure part quality and tool life.

Can the Set of standard jaws for FINN-POWER P20 press brake handle repeated bending of surface-hardened steel without premature wear?

Yes. the Set of standard jaws for FINN-POWER P20 press brake can handle repeated bending of surfaceâhardened steel without premature wear, provided normal operating limits and maintenance are observed. Because the jaws themselves are made of surfaceâhardened steel, they offer enhanced resistance to abrasion and indentation compared with untreated tooling. This hardness on the working faces reduces the rate of wear when bending tougher or abrasive materials, extending tool life under repetitive cycles. However, longâterm performance depends on several factors: - Material hardness and thickness of the workpiece: Extremely hard or highly abrasive steels will still increase wear rates compared with mild steel. Surfaceâhardened workpieces may cause faster localized wear if they exceed the jawâs hardness differential. - Bending parameters: Excessive tonnage, incorrect tooling clearance, or improper bending angles can cause concentrated stresses that accelerate wear or cause chipping. - Alignment and setup: Misalignment, poor clamping, or using the wrong jaw profile increases sliding and point loading, shortening service life. - Maintenance and inspection: Regular cleaning, lubrication of holder interfaces, and timely regrinding or replacement of worn jaws preserve performance. In summary, the Set of standard jaws for FINN-POWER P20 press brake is suitable for repeated bending of surfaceâhardened steel in typical pressâbrake use. To avoid premature wear, match the jaws to the part geometry and material, operate within recommended tonnage and clearances, and follow routine maintenance and inspection intervals.

A set of jaws standard for press crimping FINN-POWER P20

Additional information

A set of standard jaws for a FINN-POWER type P20 crimping press. Material: surface-hardened steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
FP-20-06	Set jaws 6 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-07	Set jaws 7 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-08	Set jaws 8 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-09	Set jaws 9 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-10	Set jaws 10 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-12	Set jaws 12 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-14	Set jaws 14 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-16	Set jaws 16 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-16L	Set jaws 16 mm type 20L (L=75 mm)	-	-	In stock	Enquiry
FP-20-19	Set jaws 19 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-19L	Set jaws 19 mm type 20L (L=75 mm)	-	-	In stock	Enquiry
FP-20-23	Set jaws 23 mm type 20 (L=55 mm)	-	-	In stock	Enquiry
FP-20-23L	Set jaws 23 mm type 20L (L=75 mm)	-	-	In stock	Enquiry
FP-20-27	Set jaws 27 mm type 20 (L=70 mm)	-	-	In stock	Enquiry
FP-20-27L	Set jaws 27 mm type 20L (L=75 mm)	-	-	In stock	Enquiry
FP-20-31	Set jaws 31 mm type 20 (L=70 mm)	-	-	In stock	Enquiry
FP-20-31L	Set jaws 31 mm type 20L (L=75 mm)	-	-	In stock	Enquiry
FP-20-36	Set jaws 36 mm type 20 (L=75 mm)	-	-	In stock	Enquiry
FP-20-41	Set jaws 41 mm type 20 (L=75 mm)	-	-	In stock	Enquiry
FP-20-47	Set jaws 47 mm type 20 (L=85 mm)	-	-	In stock	Enquiry
FP-20-54	Set jaws 54 mm type 20 (L=85 mm)	-	-	In stock	Enquiry