Is the Straight plug bulkhead connector, type R10 compatible with both vacuum and compressed air systems up to 16 bar and temperatures from -20Â°C to +80Â°C?

Yes. The Straight plug bulkhead connector, type R10 is specified for vacuum and compressed air, supports a working pressure up to 16 bar, and operates in the temperature range â20Â°C to +80Â°C. Its nickel-plated brass construction and NBR sealing are designed to maintain pneumatic and mechanical sealing in those conditions.

Does the Straight plug bulkhead connector, type R10 require special maintenance to preserve mechanical and pneumatic sealing over repeated assemblies?

No special maintenance is required. Straight plug bulkhead connector, type R10 is designed for easy, quick repeated assemblies without loss of mechanical or pneumatic sealing. Made of nickel-plated brass with NBR seals, it maintains sealing integrity across multiple cycles when used within specified limits (vacuum/air, up to 16 bar, â20Â°C to +80Â°C). Standard care-inspect O-rings/seals for damage, keep mating surfaces clean, and avoid exceeding pressure/temperature ratings-will ensure long-term performance.

Can the Straight plug bulkhead connector, type R10 be used with different wire gauges and component types?

Yes. the Straight plug bulkhead connector, type R10 can be used with different wire gauges and component types, within practical limits of its design. Key points: - Compatibility: Itâs intended for connecting wires and other components in pneumatic systems, so it accepts varied conductors and fittings used in such assemblies. - Sealing and reliability: Its nickel-plated brass body and NBR sealing maintain mechanical and pneumatic sealing during multiple assemblies, so mixing different wire gauges or component leads wonât inherently compromise sealing if the connector is used as intended. - Pressure and medium constraints: Suitable for vacuum and air up to 16 bar and for temperatures between â20Â°C and +80Â°C. Any wires or components introduced must tolerate these conditions and not interfere with the seal. - Practical limits: Extremely large or rigid conductors, oversized insulation, or components with incompatible tail geometries may prevent proper insertion or sealing. Likewise, very small or loose-fitting leads may require additional ferrules, sleeves, or packing to ensure reliable electrical/mechanical contact and maintain pneumatic integrity. - Recommended practice: Match the conductor or component termination to the connectorâs accepted dimensions (use appropriate ferrules, crimps, or adaptors if needed), verify sealing around the inserted element, and ensure the mateâs materials withstand the working pressure, medium, and temperature. In summary, Straight plug bulkhead connector, type R10 is adaptable to different wire gauges and component types commonly used in pneumatic systems, provided they fit the connectorâs physical dimensions and meet the pressure, medium, and temperature requirements.

Straight plug bulkhead connector, type R10

All products, Push-in fittings/

Additional information

Material	B – brass (bronze)

Straight plug-in partition fitting, type R10, designed for connecting wires and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: nickel-plated brass. Working pressure: 16 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +80°C. Sealing: NBR.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-2011002	R10 bulkhead fitting with nuts, 5 mm hose - 5 mm hose	-	16	In stock	Enquiry
MW-2011006	RL10 bulkhead fitting with nuts, 12 mm hose - 12 mm hose	-	16	In stock	Enquiry
MW-2011007	RL10 bulkhead fitting with nuts, 14 mm hose - 14 mm hose	-	16	In stock	Enquiry
MW-2011A01	R10 bulkhead fitting with nuts, hose 3.17 mm - hose 3.17 mm	-	16	In stock	Enquiry
MW-2011A02	R10 bulkhead fitting with nuts, 3 mm hose - 3 mm hose	-	16	In stock	Enquiry
MW-2L11001	RL10 bulkhead fitting with nuts, 4 mm hose - 4 mm hose	-	16	In stock	Enquiry
MW-2L11003	RL10 bulkhead fitting with nuts, hose 6 mm - hose 6 mm	-	16	In stock	Enquiry
MW-2L11004	RL10 bulkhead fitting with nuts, 8 mm hose - 8 mm hose	-	16	In stock	Enquiry
MW-2L11005	RL10 bulkhead fitting with nuts, hose 10 mm - hose 10 mm	-	16	In stock	Enquiry
MW-2L11301	RL10 reduced partition connector with nuts, 6 mm hose - 4 mm hose	-	16	In stock	Enquiry
MW-2L11302	RL10 reduced partition connector with nuts, 8 mm hose - 4 mm hose	-	16	In stock	Enquiry
MW-2L11303	RL10 reduced partition connector with nuts, 8 mm hose - 6 mm hose	-	16	In stock	Enquiry
MW-2L11304	RL10 reduced partition connector with nuts, 10 mm hose - 6 mm hose	-	16	In stock	Enquiry
MW-2L11305	RL10 reduced partition connector with nuts, 10 mm hose - 8 mm hose	-	16	In stock	Enquiry
MW-2L11306	RL10 reduced partition fitting with nuts, 12 mm hose - 6 mm hose	-	16	In stock	Enquiry
MW-2L11307	RL10 reduced partition connector with nuts, 12 mm hose - 8 mm hose	-	16	In stock	Enquiry
MW-2L11308	RL10 reduced partition fitting with nuts, 12 mm hose - 10 mm hose	-	16	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Straight plug-in partition fitting, type R10, designed for connecting wires and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: nickel-plated brass. Working pressure: 16 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +80°C. Sealing: NBR.