Is the Plug tee "Y" with spigot, type R24 compatible with fluids other than air and vacuum given its NBR sealing and -20Â°C to +60Â°C range?

Plug tee "Y" with spigot, type R24 is specified for vacuum and air only. Its sealing material is NBR (nitrile rubber) and the temperature range is â20 Â°C to +60 Â°C. These properties limit compatibility with other fluids: - NBR is generally resistant to mineral oils, greases, hydraulic oils, air and some water-based fluids, but it has poor resistance to aromatic hydrocarbons, ketones, esters, chlorinated solvents, some acids/alkalis and hot or strongly oxidative fluids. - The stated temperature range further restricts use with fluids that require higher or lower temperatures for safe sealing performance. - The product description and declared working medium (vacuum, air) indicate it was designed and tested for pneumatic use; using aggressive liquids or chemicals may impair sealing, degrade the plastic body or NBR, and void safety/performance expectations. Conclusion: You should not assume compatibility with fluids other than air and vacuum without manufacturer confirmation or material compatibility testing. For use with oils, chemicals or other liquids, consult the manufacturer for validated compatibility or choose a fitting specified for liquid service and compatible seal material.

Can the Plug tee "Y" with spigot, type R24 be used outdoors in wet or humid environments without degrading performance?

Plug tee "Y" with spigot, type R24 is made of plastic with NBR seals and is designed for pneumatic use (vacuum, air) at temperatures from -20Â°C to +60Â°C and up to 12 bar. These specifications indicate it tolerates humid environments and occasional wetting typical in pneumatic installations. However, prolonged outdoor exposure to rain, UV radiation, temperature extremes beyond the stated range, or corrosive conditions can degrade plastic and NBR over time, reducing sealing performance. For reliable long-term outdoor/wet use, consider UV-resistant materials, additional protective housing, or confirm manufacturer guidance for continuous outdoor exposure.

Does the Plug tee "Y" with spigot, type R24 allow quick disconnection/reconnection without losing pneumatic sealing?

Yes. The Plug tee "Y" with spigot, type R24 allows quick disconnection and reconnection without losing pneumatic sealing. The product description states it is designed for easy and quick use in multiple assemblies without loss of sealing on both mechanical and pneumatic sides. With NBR sealing, suitability for vacuum and air, a working pressure up to 12 bar and operating temperature range -20Â°C to +60Â°C, it is engineered to maintain pneumatic integrity during repeated connections and disconnections.

Plug tee “Y” with spigot, type R24

All products, Push-in fittings/

Additional information

Material	P – material (plastic)

Y-type plug tee with a fitting, type R24, designed for connecting wires and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: plastic. Working pressure: 12 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +60°C. Sealing: NBR.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-2024001	Y RL24 Y-connector, 4 mm stub, 2 x 4 mm hose, plastic	-	12	In stock	Enquiry
MW-2024003	Y branch connector RL24, 6 mm stub, 2 x 6 mm hose, plastic	-	12	In stock	Enquiry
MW-2L24004	Y branch connector RL24, 8 mm stub, 2 x 8 mm hose, plastic	-	12	In stock	Enquiry
MW-2L24005	Y branch connector RL24, 10 mm stub, 2 x 10 mm hose, plastic	-	12	In stock	Enquiry
MW-2L24006	Y branch connector RL24, 12 mm stub, 2 x 12 mm hose, plastic	-	12	In stock	Enquiry
MW-2L24301	Y RL24 reducing tee fitting, 6 mm spigot, 2 x 4 mm hose, plastic	-	12	In stock	Enquiry
MW-2L24303	Y RL24 reducing tee fitting, 8 mm spigot, 2 x 6 mm hose, plastic	-	12	In stock	Enquiry
MW-2L24306	Y RL24 reducing tee fitting, 10 mm stub, 2 x 8 mm hose, plastic	-	12	In stock	Enquiry
MW-2L24309	Y RL24 reducing tee fitting, 12 mm stub, 2 x 10 mm hose, plastic	-	12	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Y-type plug tee with a fitting, type R24, designed for connecting wires and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: plastic. Working pressure: 12 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +60°C. Sealing: NBR.