Is the Castor for CAMLOCK connector, steel, type R (AISI 304) suitable for food-grade applications and easy to sanitize?

The Castor for CAMLOCK connector, steel, type R (AISI 304) may be suitable for some food-related applications because AISI 304 stainless steel is corrosionâresistant, nonâporous and commonly used in food equipment. These properties make it generally easy to clean and sanitize using standard foodâgrade cleaning agents and procedures. However, suitability for foodâgrade use depends on more than just material: - AISI 304 resists corrosion and is widely accepted in food contact situations, but it can be vulnerable to chloride-induced pitting in aggressive environments (e.g., salty or highly acidic conditions). - Foodâgrade approval requires compliance with applicable standards/regulations (e.g., FDA, EU 1935/2004), which must be confirmed by the manufacturer for the specific Castor for CAMLOCK connector, steel, type R. - Design details (surface finish, weld quality, crevices, threads) affect cleanability. Smooth, polished surfaces and designs without dead legs are easier to sanitize. - Gaskets or seals used with the CAMLOCK assembly must also be foodâgrade and compatible with sanitizers. Recommendation: verify with the supplier/manufacturer that the Castor for CAMLOCK connector, steel, type R meets required foodâcontact certifications and that its surface finish and associated seals are specified for sanitary cleaning procedures appropriate to your process.

Does the Castor for CAMLOCK connector, steel, type R have any surface finish or passivation to resist corrosion?

Castor for CAMLOCK connector, steel, type R is made from AISI 304 stainless steel. AISI 304 offers inherent corrosion resistance due to its chromium-nickel stainless composition, but the product description for Ring for CAMLOCK coupling, type R does not specify any additional surface finish or chemical passivation treatment. Therefore, unless the supplier explicitly states an added passivation or coating, assume corrosion resistance relies on the base AISI 304 material only. For enhanced corrosion protection (e.g., in harsh or chlorinated environments), request confirmation from the manufacturer about any passivation, electropolishing, or protective coatings before purchasing.

Can Castor for CAMLOCK connector, steel, type R (AISI 304) be used with high-pressure steam sterilization?

Yes. Castor for CAMLOCK connector, steel, type R (AISI 304) can be used with highâpressure steam sterilization (autoclaving). AISI 304 stainless steel is widely used for components exposed to steam, heat, and repeated sterilization cycles because it resists corrosion, maintains mechanical strength at typical autoclave temperatures (121â134 Â°C), and tolerates the moist, oxidative environment of steam sterilization. However, a few practical considerations must be observed: - Ensure the entire assembly (including any seals, gaskets, or nonâmetallic parts) is compatible with highâtemperature steam; elastomers like EPDM or silicone are generally suitable, while some plastics and certain rubber compounds may degrade. - Inspect for crevices, threads, or surface damage where contamination could be trapped; proper cleaning before sterilization improves outcomes. - Verify that any surface finish, coatings, or attachments on the Castor for CAMLOCK connector are also rated for autoclave conditions. - Follow manufacturer recommendations for maximum temperature, cycle duration, and number of cycles when available. If only the Ring for CAMLOCK coupling, type R (Material: AISI 304 steel) is specified, the AISI 304 component itself is suitable for autoclaving, but confirm compatibility of the complete Castor for CAMLOCK connector, steel, type R assembly before routine use.

Ring handle for coupling CAMLOCK, steel, type R

Additional information

Material	SS – stainless steel

Ring handle for coupling CAMLOCK, type R. Material: steel AISI 304.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AC-R-050	Ring handle R 1/2"-1"	-	-	In stock	Enquiry
AC-R-050X	Ring handle R 1/2" ÷ 1"	-	-	In stock	Enquiry
AC-R-200	Ring handle R 1.1/4"-2.1/2"	-	-	In stock	Enquiry
AC-R-200X	Ring handle R 1.1/4" ÷ 2.1/2"	-	-	In stock	Enquiry
AC-R-300	Ring handle R 3" ÷ 6"	-	-	In stock	Enquiry