Is the Adaptor - elbow 90Â° with GW BSP, carbon steel, type A115A suitable for use with hydraulic systems operating at high pressures and does its internal BSP flat sealing ensure leak-free connections?

Adaptor - elbow 90Â° with GW BSP, carbon steel, type A115A Format is designed as a 90Â° high-pressure adapter with internal BSP thread and flat sealing, made of galvanized carbon steel. Its construction from carbon steel and galvanization gives it good mechanical strength and corrosion resistance suitable for many hydraulic applications. The internal BSP flat sealing (G-thread) provides a metal-to-metal or flat-face seal that, when assembled correctly with the appropriate mating part and under recommended torque, can achieve reliable, low-leakage connections for high-pressure systems. However, suitability for a specific high-pressure hydraulic system depends on the exact pressure rating, fluid type, temperature, dynamic loads and compatibility with system fittings. The product description does not specify maximum working pressure, sealing surface finish, or certification standards. Before use in critical high-pressure applications, verify the adapterâs rated working pressure, material compatibility with the hydraulic fluid, and compliance with applicable standards; ensure correct installation (clean threads, proper torque, and mating flat-face counterpart) and consider pressure testing or manufacturer documentation to confirm leak-free performance.

Can the Adaptor - elbow 90Â° with GW BSP, carbon steel, type A115A be used with corrosive fluids given its galvanized finish?

Adaptor - elbow 90Â° with GW BSP, carbon steel, type A115A has a galvanized finish which offers some corrosion resistance, but it is not suitable for prolonged contact with strongly corrosive fluids or highly aggressive environments. Galvanizing protects against atmospheric corrosion and mild chemical exposure, but it can degrade when exposed to acids, alkalis, chlorides, or other aggressive media. For corrosive fluids, select materials specifically resistant to the fluid (e.g., stainless steel, duplex, or appropriate coatings/linings) and verify chemical compatibility and pressure/temperature limits. If unsure, consult the manufacturer or a corrosion specialist before use.

Does the Adaptor - elbow 90Â° with GW BSP, carbon steel, type A115A require specific torque values for its internal BSP flat sealing?

Adaptor - elbow 90Â° with GW BSP, carbon steel, type A115A does not require specific torque values for its internal BSP flat sealing in the same way as thread-and-seat or metal-to-metal tapered connections. BSP flat sealing (also called BSPP or parallel thread with flat face) achieves leak-tightness by compressing a flat gasket or the mating flat surfaces rather than relying on thread deformation. Key practical guidance: - Use a competent wrench and tighten until the flat sealing face is fully engaged and a positive compressive load on the sealing surface or gasket is achieved. - Avoid excessive torque: over-tightening can damage the flat sealing face, crush gaskets, strip threads, or induce distortion in the adapter. - If a gasket or O-ring is used, follow the gasket manufacturerâs recommended compressive load or installation instructions. - If tightening into a port or mating fitting with a specified torque (by the equipment maker), follow that equipment specification. - For repeatability and safety in critical/high-pressure systems, use a torque wrench and establish an installation procedure by testing assemblies at working pressure to confirm leak-free performance. - Ensure threads are clean, undamaged, and properly lubricated if recommended for the sealing system in use. In summary, there is no universal numeric torque value provided for Adaptor - elbow 90Â° with GW BSP, carbon steel, type A115Aâs internal BSP flat sealing; tighten to achieve full face contact without over-torquing, or follow gasket/equipment-specific torque recommendations where applicable.

Adapter – elbow 90° with BSP female, carbon steel, type A115A

All products, High-pressure adapters/

Additional information

Material	CS – steel (cast iron)

High-pressure 90° adapter type A115A with BSP female thread (flat sealing). Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-A115A-02	Adapter 90° 1/8" BSP female / 1/8" BSP female	-	350	In stock	Enquiry
TI-A115A-04	Adapter 90° 1/4" BSP female / 1/4" BSP female	-	350	In stock	Enquiry
TI-A115A-06	Adapter 90° 3/8" BSP female / 3/8" BSP female	-	250	In stock	Enquiry
TI-A115A-08	Adapter 90° 1/2" BSP female / 1/2" BSP female	-	225	In stock	Enquiry
TI-A115A-12	Adapter 90° 3/4" BSP female / 3/4" BSP female	-	200	In stock	Enquiry
TI-A115A-16	Adapter 90° 1" BSP female / 1" BSP female	-	160	In stock	Enquiry
TI-A115A-20	Adapter 90° 1.1/4" BSP female / 1.1/4" BSP female	-	160	In stock	Enquiry
TI-A115A-24	Adapter 90° 1.1/2" BSP female / 1.1/2" BSP female	-	160	In stock	Enquiry
TI-A115A-32	Adapter 90° 2" BSP female / 2" BSP female	-	125	In stock	Enquiry