Is the Adaptor - elbow 90Â° with GZ / GW BSP, carbon steel, type A114C compatible with hydraulic systems using mineral oil and pressures up to 420 bar?

Yes. The Adaptor - elbow 90Â° with GZ / GW BSP, carbon steel, type A114C is suitable for hydraulic systems using mineral oil at pressures up to 420 bar, provided system compatibility checks are met. Reasoning: the item is described as a 90Â° high-pressure adaptor, âcompactâ type A114C, made of carbon steel and galvanized, with 60Â° cone seals on both the external BSP thread and the internal BSP thread plus a swivel nut; these design features (60Â° cone sealing and carbon steel construction, galvanized finish) are typical for high-pressure hydraulic fittings and are compatible with mineral oils. Ensure correct thread type and size, proper torque on the swivel nut, and that temperature, dynamic loads, and any specific fluid additives or contaminants in your system fall within the fittingâs ratings. If in doubt, confirm the manufacturerâs pressure rating and material compatibility certificate for your exact operating conditions.

Does the Adaptor - elbow 90Â° with GZ / GW BSP, carbon steel, type A114C require specific torque values for the swivel nut installation?

Adaptor - elbow 90Â° with GZ / GW BSP, carbon steel, type A114C Format: The product description (90Â° high-pressure adaptor type A114C with external BSP thread (60Â° cone seal) and internal BSP thread, with swivel nut (60Â° cone seal), "compact" version. Material: carbon steel, galvanized) does not include specific torque values for the swivel nut installation. For safe and reliable assembly, follow general best practices: use manufacturerâs torque data if available, tighten by hand until seated then apply an appropriate wrench torque for the size and thread per relevant standards (BSP/ISO 7â1), avoid overâtorquing which can damage the 60Â° cone seal, and if used in highâpressure systems, perform a pressure test after assembly. If exact torque is required, contact the manufacturer/supplier or refer to their installation data sheet.

Can Adaptor - elbow 90Â° with GZ / GW BSP, carbon steel, type A114C be used in systems with temperature extremes (freezing or high heat)?

Adaptor - elbow 90Â° with GZ / GW BSP, carbon steel, type A114C Format: suitability for temperature extremes depends on materials and seals. The body is carbon steel, galvanized, which provides good mechanical strength and corrosion resistance in typical temperature ranges. Carbon steel remains structurally sound from moderately low temperatures (around -20Â°C to -40Â°C depending on grade) up to high temperatures (typically up to ~200Â°C) before strength and coating performance degrade. However, the galvanized coating can be affected by very high temperatures (zinc begins to oxidize and flow above ~250â300Â°C) and by thermal cycling that can promote coating cracking. Most critical for extreme temperatures are the sealing surfaces and any internal seals (e.g., PTFE, elastomers) and the 60Â° cone metal-to-metal sealing design. The 60Â° cone metal seal can perform well at both low and high temperatures because it is a metal-to-metal contact and does not rely on elastomeric materials, provided the mating surfaces remain undamaged and correct assembly torque is used. If the adaptor uses elastomer O-rings or bonded seals anywhere, their temperature limits must be checked: common elastomers (NBR, EPDM, Viton) have specific ranges (e.g., NBR ~-30Â°C to +120Â°C, Viton ~-20Â°C to +200Â°C). Freezing conditions can stiffen or embrittle some elastomers; high heat can cause hardening, swelling or loss of sealing. Recommendation: For use in freezing or high-heat systems, verify the exact carbon steel grade, the galvanizing type and thickness, andâcriticallyâthe seal materials and whether the connection is purely metal-to-metal. If the assembly relies solely on the 60Â° cone metal seal and suitable torque, the adaptor is generally suitable for wide temperature ranges. If elastomer seals are present, confirm their rated temperature range for your application. For extreme or safety-critical services, consult the manufacturerâs datasheet and perform application-specific validation (temperature cycling, pressure rating at temperature, corrosion exposure).

Adaptor – elbow 90° with GZ / GW BSP, carbon steel, type A114C

All products, High-pressure adapters/

Additional information

Material	CS – steel (cast iron)

90° high-pressure adaptor type A114C with external BSP thread (60° cone seal) and internal BSP thread, with swivel nut (60° cone seal), “compact” version. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-A114C-02	90° Adapter GZ BSP 1/8" / GW BSP 1/8"	-	400	In stock	Enquiry
TI-A114C-04	90° Adapter GZ BSP 1/4" / GW BSP 1/4"	-	400	In stock	Enquiry
TI-A114C-06	90° Adapter GZ BSP 3/8" / GW BSP 3/8"	-	400	In stock	Enquiry
TI-A114C-08	90° Adapter GZ BSP 1/2" / GW BSP 1/2"	-	350	In stock	Enquiry
TI-A114C-12	90° Adapter GZ BSP 3/4" / GW BSP 3/4"	-	315	In stock	Enquiry
TI-A114C-16	90° Adapter GZ BSP 1" / GW BSP 1"	-	250	In stock	Enquiry
TI-A114C-20	90° Adapter GZ BSP 1.1/4" / GW BSP 1.1/4"	-	200	In stock	Enquiry
TI-A114C-24	90° Adapter GZ BSP 1.1/2" / GW BSP 1.1/2"	-	160	In stock	Enquiry
TI-A114C-32	90° Adapter GZ BSP 2" / GW BSP 2"	-	125	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

90° high-pressure adaptor type A114C with external BSP thread (60° cone seal) and internal BSP thread, with swivel nut (60° cone seal), “compact” version. Material: carbon steel, galvanized.